Respironics bilichek Скачать руководство пользователя

Страница: 18 / 36

BiliChek Service Manual

1014988

11.0 Troubleshooting Guide

Display Window

Indication

Solution

E00

No user set-up information identified.

Install a charged battery pack into the HHU. Press

and

at the same time, hold for one second and then release. This

places the HHU in the Set-up mode. Enter settings specific to your

institution. See section 10.0 of this manual for Set-up Mode

instructions.

E01

Calibration measurement is unacceptable.

Press and release

and

at the same time.

Ensure Bili

Cal

tip is in place and retry the calibration. If the error

continues: 1. Place a

fully charged

Battery Pack in the HHU, install a

new BiliCal Tip, and try again to calibrate several times.

2. Remove and rotate the Bili

Cal

tip and retry. 3. Replace the measurement

light bulb (see Section 14.1 for instructions) and retry. If the error is still

present, the HHU has malfunctioned and requires service. Call

Respironics or your distributor.

E02

Patient measurement is unacceptable.

Press and release

and

at the same time. Take another

measurement. If E02 occurs again, replace the Bili

Cal

tip, repeat

calibration and retry the measurement. If the error is still present, the

HHU has malfunctioned and requires service. Call

Respironics or your distributor.

E03

Bili

Cal

Individual Calibration Tip removed

Press and release

and

at the same time.

between calibration and measurement scan.

Remove the Bili

Cal

Individual Calibration Tip.

Replace with a new tip and recalibrate.

E04

Too much movement during measurement.

Press and release

and

at the same time.

Perform another measurement.

E05

High Measurement is out of clinically proven range.

Obtain a Total Serum Bilirubin level (TSB)

E10

Light bulb is burned out.

Replace measurement light bulb (see section 14.1 for instructions). If

error continues, the HHU has malfunctioned and requires service. Call

Respironics or your distributor.

E99

System error is detected.

Call for Service.

Low battery pack. Maximum of 10 measurements left.

Replace current battery pack with a fully

charged battery pack from the charger base and place the discharged

battery in well B for charging.

Discharged Battery pack.

Replace current battery pack with a fully charged one from the charger

No measurements can be taken.

base. Place the discharged battery pack into well B for charging.

Display

Window

Indication

Solution

11.1 Troubleshooting Guide

Содержание bilichek





































Результаты поиска

Содержание bilichek

Отзывы:

Похожие инструкции для bilichek

Бренды по названию

Популярные бренды

Respironics bilichek, Руководство по обслуживанию

Результаты поиска

Содержание bilichek

Отзывы:

Похожие инструкции для bilichek

Бренды по названию

Популярные бренды