resideo V250FBPT Скачать руководство пользователя страница 57

Страница: 57 / 80

– 57 –

Testing the System

(To Be Conducted Weekly)

Using the 5 TEST Key

The

TEST

key puts your system into Burglary Walk Test mode, which allows each burglary

protection point to be checked for proper operation.

1. Disarm the system and close all protected windows, doors, etc. READY should be

displayed.

TEST

2. Enter your security code and press the 5 key.
3. The external sounder should sound for 3 seconds and then turn off. If the sounder does

not sound, it may be due to dialer communication activity. Wait a few minutes and try

again. If the sounder still does not sound, CALL FOR SERVICE IMMEDIATELY.

4. The keypad will sound a single beep every 15 seconds as a reminder that the system is

in Test mode. Each time a protection zone is faulted (opened); the keypad should beep

three times. If the sounder does not sound, CALL FOR SERVICE IMMEDIATELY.

NOTES:

•

No alarm reports will be sent to the central monitoring station while the system

is in Test mode.

•

The system will automatically exit the Test mode if there is no activity (no doors or

windows are opened and closed, no motion detectors are activated, etc.) for 60 minutes.

The system will beep the keypad(s) twice every 5 seconds during the last 5 minutes as a

warning that it is about to exit the Test mode and return to normal operation.

Testing Your System

1. Open and close each protected door and window in turn and listen for three beeps. Each

faulted protection point should appear on the display.

2. Walk in front of any motion detectors (if used) and listen for three beeps as movement is

detected (wireless motion detectors have a 3-1/2 minute lockout between trips). Each

detector’s should appear on the display when it is activated.

3. Follow the manufacturer's instructions to test all smoke detectors to ensure that all are

functioning properly. Each detector should appear on the display when activated.

4. When all protection points have been checked, there should be no zone identification

numbers displayed. If a problem is experienced with any protection point (no confirming

sounds, no display), CALL FOR SERVICE IMMEDIATELY.

Turn off Test mode by entering the security code + the

OFF

key.

Содержание V250FBPT

















































































Результаты поиска

Содержание V250FBPT

Отзывы:

resideo V250FBPT, Руководство пользователя, Страница: 57 / 80

Результаты поиска

Содержание V250FBPT

Отзывы: