Renesas mPD98431 Скачать руководство пользователя страница 89

Страница: 89 / 127

CHAPTER 4 REGISTER DESCRIPTION

User’s Manual S14054EJ4V0UM

RSVREG - Receive status register (register address A[7:0] = 95H) Read only

RBYT

RLENE

VLAN

USOP

RPCF

RCFR

DBNB

RBRO

RMUL

RXOK

RLOR

RLER

RCRCE

RCV

CEPS

REPS

PAIG

This register indicates an interrupt source when the INT# signal is made low by the status of a receive packet

(except bits 31 through 16). If the interrupt of each bit occurs, the corresponding bit is set to 1 and the INT# signal is

made low. If an interrupt is caused by the source masked by the RIMR register, only the corresponding bit of this

This register is updated each time the MAC module receives a packet.

If this register is read when the SRRC bit of the MISCR register is set to 1, all the bits are automatically cleared.

(1/2)

Bit

Name

Function

Default

31:16

RBYT

Receive byte count.

This field indicates the length of the received packet in byte units.

–

RLENE

Receive packet length error.

When this bit is 1, it indicates that the length of the receive packet is less

than 64 octet or greater than 1518 octet. (less than 64 octet or greater than

1522 octet in the case of VLAN)

VLAN

VLAN frame.

When this bit is 1, it indicates that the VPID field of the received packet

coincides with the value of the VLTP register. This bit is not set to 1 if a

CRC error or RXER occurs.

USOP

Reception of control frame including undefined op code.

When this bit is 1, it indicates that a control frame including an undefined

op code has been received. This bit is not set to 1 if a CRC error occurs.

RPCF

Pause control frame reception.

When this bit is 1, it indicates that a pause control frame has been

received. This bit is not set to 1 if a CRC error occurs.

RCFR

Control frame reception.

When this bit is 1, it indicates that a control frame has been received. This

bit is not set to 1 if a CRC error occurs.

DBNB

Reception of a packet including dribble nibble.

When this bit is 1, it indicates that a dribble nibble has occurred in the

received packet.

RBRO

Broadcast packet reception.

When this bit is 1, it indicates that a broadcast packet has been received.

RMUL

Multicast packet reception.

When this bit is 1, it indicates reception of a multicast packet or a broadcast

packet.

RXOK

End of reception

When this bit is 1, it indicates that reception has been completed. This bit

is not set to 1 if a CRC error or RXER occurs.

Содержание mPD98431
































































































































Результаты поиска

Содержание mPD98431

Отзывы:

Бренды по названию

Популярные бренды

Renesas mPD98431, Руководство пользователя

Результаты поиска

Содержание mPD98431

Отзывы:

Бренды по названию

Популярные бренды