manualshive.com logo in svg

Renesas mPD98431, Руководство пользователя

Поделиться
Скачать
Renesas mPD98431 Скачать руководство пользователя страница 21

CHAPTER  2   PIN  FUNCTIONS

User’s Manual  S14054EJ4V0UM

19

(3/3)

Pin Name

Pin No.

I/O

Function

RXFDQ[3:0]/

FDQ[3:0]

204, 12, 111, 203

O / O/I,

3-state

Receive data attribute/FIFO bus attribute.

These signals indicate the attribute of data on the FIFO bus.  The functions of

these signals differ as follows depending on the bus mode:

(1) 32-bit dual bus mode

These signals function as RXFDQ[3:0] and output the attribute of the

receive data output onto RXFD[31:0] when the FIFO bus is accessed by

the receive FIFO for read.  For the output pattern of RXFDQ[3:0], refer to

Table 3-3

.

(2) 64-bit single bus mode

These signals function as FDQ[3:0] and input the attribute of the transmit

data on FD[63:0] when the transmit FIFO is accessed for write.  When

the receive FIFO is accessed for read, the attribute of the receive data

output onto FD[63:0] is output.  For the input pattern and output pattern

of FDQ[3:0], refer to 

Tables 3-2

 and 

3-4

.

TXFDQ[3:0]

247, 67, 162, 248

I

Transmit data attribute.

These signals indicate the attribute of the transmit data on the FIFO bus in

the 32-bit dual bus mode.  They indicate the attribute of the transmit data on

FD[63:0] when the transmit FIFO is accessed for write.  For the input pattern

of TXFDQ[3:0], refer to 

Table 3-1

.  These signals are meaningless in the 64-

bit single bus mode.

TXFBA[7:0]

156, 61, 245, 157,

62, 246, 159, 158

O,

3-state

Transmit FIFO buffer available.

When these signals are high, the transmit FIFO has space to which transmit

data can be written.  If the quantity of the data in the transmit FIFO exceeds

the value set to the TFDMH field of the TFIC register, these signals go low.

A TXFBA signal is provided for each port, and TXFBA[n] is the TXFBA signal

of port n.

RXFA

113

O,

3-state

Receive frame available.

When this signal is high, the port indicated by RXFPT has at least one packet

from the receive data stream that is ready to be transferred to the host

system.

PASS

249

I

Receive frame pass.

This signal is input to start transfer of the receive data currently on the FIFO

bus when the bus is accessed by the receive FIFO for read.

SKIP

69

I

Receive frame skip.

This signal is input to skip the port currently on the FIFO bus and read data

from the next port when the FIFO bus is accessed by the receive FIFO for

read.

Содержание mPD98431
































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды