Renesas IDT Tsi574 Скачать руководство пользователя страница 222 | Manualshive

Страница: 222 / 514

Renesas IDT Tsi574 Скачать руководство пользователя страница 222

11. Signals > Signal Groupings

222

Tsi574 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

I2C_SEL

I, LVTTL,
PU

I

2

C Pin Select.

Together with the I2C_SA[1,0] pins, the Tsi574
determines the lower 2 bits of the 7-bit address of
the EEPROM address it boots from.

When asserted, the I2C_SA[1,0] values are also
be used as the lower two bits of the EEPROM
address.

When de-asserted, the I2C_SA[1,0] pins are
ignored and the lower two bits of the EEPROM
address are default to 00.

The values of the lower two bits of the EEPROM
address can be over-ridden by software after
reset.

No termination required. Internal
pull-up can be used for logic 1.

Pull up to VDD_IO through a
10K resistor if external pull-up is
desired. Pull down to VSS_IO to
change the logic state.

JTAG / TAP Controller

TCK

I, LVTTL,
PD

IEEE 1149.1/1149.6 Test Access Port
Clock input

Pull up to VDD_IO through a
10K resistor if not used.

TDI

I, LVTTL,
PU

IEEE 1149.1/1149.6 Test Access Port
Serial Data Input

Pull up to VDD_IO through 10K if
not used or if higher edge rate is
required.

TDO

O, LVTTL

IEEE 1149.1/1149.6 Test Access Port
Serial Data Output

No connect if JTAG is not used.
Pull up to VDD_IO through a
10K resistor if used.

TMS

I, LVTTL,
PU

IEEE 1149.1/1149.6 Test Access Port
Test Mode Select

Pull up to VDD_IO through a
10K resistor if not used.

TRST_b I,

LVTTL,

PU

IEEE 1149.1/1149.6 Test Access Port
TAP Reset Input

This input must be asserted during the assertion of
HARD-RST_b. Afterwards, it can be left in either
state.

Combine the HARD_RST_b and TRST_b signals
with an AND gate and use the output to drive the
TRST_b pin.

Tie to VSS_IO through a 10K
resistor if not used.

BCE

I, LVTTL,
PU

Boundary Scan compatibility enabled pin. This
input is used to aid 1149.6 testing.

This signal also enables system level diagnostic
capability using features built into the SerDes. For
more information on this functionality, refer to the
Serial RapidIO Signal Analyzer documentation
available on the IDT website.

This signal must be tied to VDD_IO during normal
operation of the device, and during JTAG
accesses of the device registers

This signal should have the
capability to be pulled-up or
pulled-low.

• The default setting is to be

pulled-up.

• Pulling the signal low enables

the signal analyzer
functionality on the SerDes

• A 10K resistor to VDD_IO

should be used.

Table 31: Tsi574 Signal Descriptions (Continued)

Pin Name

Type

Description

Recommended Termination

a

«
...
220
221
222
223
224
...
»

Содержание IDT Tsi574



































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды