7
TROUBLESHOOTING
NOTICE:
For additional help and information you can visit
www.remingtonpowertools.com
WARNING:
Before you service the chain saw always unplug it from the main power
outlet. Otherwise severe injury or death may occur from electrical shock. Bodily injury may
also occur from accidental contact with the moving chain.
OBSERVED FAULT
POSSIBLE CAUSE
REMEDY
Chain saw runs but it does not cut.
Chain may be assembled backwards on guide bar.
See Chain Saw Assembly instructions, pages 3 and 6.
Chain saw does not cut unless heavily forced. Cutting
produces only sawdust with few large chips.
Chain is dull.
See sharpening saw chain, page 6.
Chain saw runs slow. Chain saw stalls easily.
Low power supply voltage.
Extension cord wire size too small. See extension cords page 4.
Motor of chain saw does not run when you squeeze trigger.
1. Trigger lock-out not pressed in to release trigger.
2. Extension cord connections loose.
3. Open line fuse or circuit-breaker.
4. Worn-out motor brushes.
5. Open wiring circuit on saw.
1. Press in trigger lock out before squeezing trigger.
2. Check cord connections.
3. Check line fuse or circuit breaker.
4. See authorized service centre.
5. See authorized service centre.
Motor of chain saw runs, but the chain does not move.
Drive sprocket failure.
Remove and inspect drive sprocket for damage.
Chain does not get oil.
1. Clogged oil slot in guide bar.
2. Oil is too thick.
1. Remove guide bar and clean oil slot.
2. Use correct weight of oil. See filling oil tank page 6.
Chain comes off guide bar.
1. Chain is loose.
2. Guide bar and chain not assembled correctly.
1. Tighten chain. See saw chain tension adjustment page 6.
2. See chain saw assembly pages 3 and 6.
Chain saw smokes.
Saw damaged. Do not use saw.
See authorized service centre.
Chain saw leaks oil.
It is normal for oil to seep when the saw is not in use.
Note: empty oil tank when not in use.
CLEANING AND STORAGE
If you intend to store the chain saw and pole assembly for more than 30 days, it is recommended to
follow these steps:
1. Drain the oil tank after each use.
2. Remove and clean the guide bar and chain. Clean the guide bar and chain by soaking in a
petroleum based solvent or a mild soap and water mixture.
3. Dry the guide bar and chain.
4. Place the chain in container filled with oil to prevent it rusting.
5. Wipe a thin coating of oil over the surface of the guide bar.
6. Wipe off the outside of the chain saw body and the pole assembly. Do this with a soft cloth
dampened with a mild soap and water mixture.
7. Store the chain saw up high, in a dry, locked place that is out of the reach of children.
Replacing Saw Chain
Replace the chain when the cutters are too worn to sharpen or when the chain breaks. Only use the
replacement chain that is noted in this manual. Always include a new drive sprocket when replacing
the chain. This will maintain proper driving of chain.
NOTE: For the correct part number information see the Safety Information section.
REPAIR SERVICE
WARNING:
Use only the replacement parts and accessories that are described in this
manual. Use of any other parts or accessories could damage the chain saw or injure the
operator.
For service, please call the Customer Service Department to obtain a list of authorized service dealers
near you. Service on this unit, both within and after the warranty period, should only be performed by
an authoried and approved service dealer.
Call 1-866-206-2707 (in Canada call 1-877-696-5533 or visit
www.remingtonpowertools.com
Replacing Parts and Accessories
For original replacement parts and accessories call 1-866-206-2707 (in Canada call 1-877-696-5533).
Or visit
www.remingtonpowertools.com
SPECIFICATIONS*
Type .............................................................................................................................................. Electric
Motor .................................................................................................................................120 AC 8 Amp
Motor Speed ................................................................................................................ 5900 - 6300 RPM
Guide Bar Length ................................................................................................................................10”
Guide Bar Type .................................................................................................................. Non-roller Tip
Chain Pitch .........................................................................................................................................3/8”
Bar Lube Reservoir Capacity ..........................................................................................................1.4 oz
Weight ............................................................................................................................................9.2 lbs
*All specifications are based on the latest product information available at the time of printing. We
reserve the right to make changes at any time without notice.
Содержание RM1015SPS
Страница 23: ...24 NOTES ...
