Rem GrainVac VR12 Скачать руководство пользователя

Страница: 15 / 100

REM - G

RAIN

VR12

2. S

AFETY

2.9. S

AFETY

ECALS

9000-00-0042 R3

Figure 2.2 Safety Decal Locations - Front View

WARNING

ENTANGLEMENT HAZARD

To prevent serious injury or death:

• Keep body, hair, and clothing away from rotating

pulleys, belts, chains, and sprockets.

• Do not operate with any guard removed or

modified. Keep guards in good working order.

• Shut off and remove key or lock out power source

before inspecting or servicing machine.

Made in Canada

P1513002

PART #: P1513106

PART #: P1513108

PART #: P1513100

PART #: P1513114

PART #: P1513002

(LOCATION SHOWN FOR SHEAR SPROCKET)

PART #: P1513120

PART #: P1513104

WARNING

PINCH POINT HAZARD

KEEP AWAY

To prevent serious injury or death from pinching:

• Stay away from auger tubes when opening/closing

• Keep others away

P1513120

Made in Canada

DANGER

ELECTROCUTION HAZARD

To prevent serious injury or death:

Stay away from overhead electrical wires when
adjusting auger or moving machine. Electrocution can
occur without direct contact.

P1513106

Made in Canada

CAUTION

• Read Operator’s Manual before using.

• Place all controls in neutral, stop engine, set park

brake, remove ignition key and wait for all moving
parts to stop before servicing, adjusting, repairing
or unplugging.

• Install and secure all shields before operating.

• Keep hands, feet, hair and clothing away from

moving parts.

• Clear the area of bystanders, especially small

children, before starting.

• Chock tractor and machine wheels when operating.

• Stay away from overhead electrical wires when

adjusting auger and moving machine. Electrocution
can occur without direct contact.

• Attach securely to towing and power unit using

a pin with retainer and safety chain.

• Install extra lights or use pilot vehicles when

transporting during times of limited visibility.

• Use hazard flashers when transporting.

• Wear hearing protection for prolonged exposure

to excessive noise.

• Review safety instructions annually.

P1513104

Made in Canada

100 HOURS

P1513100

Made in Canada

NOTICE

OIL CHAIN

DAILY

P1513114

Made in Canada

DANGER

HIGH SUCTION/ROTATING PARTS

To prevent being pulled involuntarily into rotating blower and/
or auger:

• Keep clothing and yourself well clear and others away from

all open inlet and discharge area

• Never open or close inspection doors unless grain vac has

been shut off and all moving parts have stopped completely

Failure to heed this warning may result in serious injury,
dismemberment, or death.

P1513108

Made in Canada

Содержание GrainVac VR12





































































































Результаты поиска

Содержание GrainVac VR12

Отзывы:

Похожие инструкции для GrainVac VR12

Бренды по названию

Популярные бренды

Rem GrainVac VR12, Руководство по эксплуатации

Результаты поиска

Содержание GrainVac VR12

Отзывы:

Похожие инструкции для GrainVac VR12

Бренды по названию

Популярные бренды