Rem GrainVac VR12 Скачать руководство пользователя | Manualshive

Страница: 19 / 100

background image

REM - G

RAIN

V

AC

VR12

2. S

AFETY

2.9. S

AFETY

D

ECALS

9000-00-0042 R3

19

Figure 2.6 Safety Decal Locations - Inlet Side View

PART #: P1513102

PART #: P1513016

PART #: P1513112

PART #: P1513108

OPEN

C

LO

SE

D

TOWARDS

INLET SIDE

P15

131

02

DANGER

SUFFOCATION HAZARD

• Follow safety precautions in equipment operator’s manual, and

know the recommended emergency procedure.

• Station an observer nearby who can communicate with both

the person in the bin and another individual to shut down
operating equipment in an emergency. To avoid anyone else
from becoming entrapped in the grain, the bin should not be
entered until it is safe.

• Grain vacuum operators should be very cautious when working

with grain that will not flow, sticks together or has spoiled.

• Grain vacuum operators should move the vacuum intake

frequently to avoid formation of a cone depression, keeping the
grain surface level working from the outside wall and moving
inward, thereby reducing the risk of engulfment.

P1513109

Made in Canada

CAUTION

Hearing
protection
required
during
operation.

Made in Canada

P1513103

DANGER

HIGH SUCTION/ROTATING PARTS

To prevent being pulled involuntarily into rotating blower and/
or auger:

• Keep clothing and yourself well clear and others away from

all open inlet and discharge area

• Never open or close inspection doors unless grain vac has

been shut off and all moving parts have stopped completely

Failure to heed this warning may result in serious injury,
dismemberment, or death.

P1513108

Made in Canada

DANGER

ROTATING FLIGHTING HAZARD

To prevent death or serious injury:

• KEEP AWAY from rotating auger flighting.

• DO NOT remove or modify auger flighting guards,

doors, or covers. Keep in good working order. Have
replaced if damaged.

• DO NOT operate the auger without all guards, doors,

and covers in place.

• NEVER touch the auger flighting. Use a stick or other

tool to remove an obstruction or clean out.

• Shut off and lock out power to adjust, service, or clean.

Made in Canada

P1513016

PART #:
P1513103

PART #: P1513109

WARNING

TIPPING HAZARD

Place jack to the location shown, for added
stability while in use, or GrainVac may tip
over during use. See Operator’s Manual for
more details.

P1513112

Made in Canada

«
...
17
18
19
20
21
...
»

Содержание GrainVac VR12





































































































Отзывы:

Нет отзывов

Похожие инструкции для GrainVac VR12

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: Macht Dental Страницы: 8

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: Mach Страницы: 12

Бренд: Zell Страницы: 32

Бренд: Uflex Страницы: 16

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: +GF+ Страницы: 2

Unity for Pro-Flex Pivot

Бренд: Össur Страницы: 40

ICELOCK 234 LANYARD

Бренд: Össur Страницы: 94

Бренд: Össur Страницы: 115

Бренд: Össur Страницы: 253

BOMAG BVP 12/50 A

Бренд: Fayat Страницы: 105

HALO miniLUME LA5300

Бренд: Cooper Lighting Страницы: 2

Бренд: Free The Tone Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды