Rem GrainVac VR12 Скачать руководство пользователя

Страница: 13 / 100

REM - G

RAIN

VR12

2. S

AFETY

2.6. R

OTATING

ARTS

AFETY

9000-00-0042 R3

• Check all hydraulic components are tight and in good condition. Replace any worn,

cut, abraded, flattened, or crimped hoses.

• Clean the connections before connecting to equipment.

• Do not attempt any makeshift repairs to the hydraulic fittings or hoses with tape,

clamps, or adhesive. The hydraulic system operates under extremely high pressure;
such repairs will fail suddenly and create a hazardous and unsafe condition.

Lockout

• Always place all hydraulic controls in neutral and relieve system pressure before dis-

connecting or working on hydraulic system.

2.6. Rotating Parts Safety

• Keep body, hair, and clothing away from

rotating pulleys, belts, chains, and sprock-
ets.

• Do not operate with any guard removed or

modified. Keep guards in good working
order.

• Shut off and remove key or lock out power source before inspecting or servicing

machine.

2.7. Rotating Flighting Safety

• KEEP AWAY from rotating flighting.

• DO NOT remove or modify flighting guards, doors, or

covers. Keep in good working order. Have replaced if
damaged.

• DO NOT operate the equipment without all guards,

doors, and covers in place.

• NEVER touch the flighting. Use a stick or other tool to remove an obstruction or

clean out.

• Shut off and lock out power to adjust, service, or clean.

2.8. Tire Safety

• Failure to follow proper procedures when mounting a

tire on a wheel or rim can produce an explosion that
may result in serious injury or death.

• DO NOT attempt to mount a tire unless you have the

proper equipment and experience to do the job.

• Have a qualified tire dealer or repair service perform

required tire maintenance.

Содержание GrainVac VR12





































































































Результаты поиска

Содержание GrainVac VR12

Отзывы:

Похожие инструкции для GrainVac VR12

Бренды по названию

Популярные бренды

Rem GrainVac VR12, Руководство по эксплуатации

Результаты поиска

Содержание GrainVac VR12

Отзывы:

Похожие инструкции для GrainVac VR12

Бренды по названию

Популярные бренды