Rem GrainVac VR12 Скачать руководство пользователя

Страница: 39 / 100

REM - G

RAIN

VR12

4. O

PERATION

4.8. G

RAIN

ACUUM

PERATION

ROCEDURE

9000-00-0042 R3

4.8. Grain Vacuum Operation Procedure

The GrainVac has been attached to the tractor, positioned, and set-up at the work site.
Position the grain truck or grain cart under the end dump spout of the GrainVac
unloading auger.

To operate grain vacuum, proceed as follows:

1. Check all items on the Pre-Operational Checklist (see page 31).

2. Make sure you and others in the work area are wearing the proper personal

protective equipment (see page 10).

Important:

Read Section 4.8.1. Applications & Characteristics of Hoses & Tubes on page 45 for the
best use of the supplied hoses.

Important:

Read Section 4.8.2. The “9 S’s of GrainVac Performance” on page 45 for detailed
instructions on maintaining the highest level of performance.

3. Prepare your hoses prior to starting the tractor or GrainVac, and lay them near or on

the grain.

Note:

Preparation of hoses prior to starting the tractor or GrainVac minimizes the time involved
in hose changes later.

4. Insert tractor ignition key and make sure park brake is set and controls are in

neutral. Start the tractor.

5. With the tractor engine at low idle, SLOWLY turn on the PTO clutch.

Always start the machine gently at low speed to prevent component
overloading and for maximum GrainVac lifespan.

Do not operate GrainVac in excess of 1000 rpm. Failure to follow
these instructions may result in machine component damage or
failure.

6. Slowly bring the PTO speed up to 1000 rpm.

7. Using the combination of hoses shown in Figure 4.8, insert the end of the intake

hose into the grain and proceed with vacuuming the grain to draw down the grain in
the bin.

Figure 4.8 Recommended Hose Configuration for Bin Load-Out

ALUMINUM BIN
LOAD-OUT NOZZLE

SHORT OR LONG STAINLESS
STEEL FLEX HOSE(S)

TELESCOPING INLET

SPARE
SHEAR
BOLTS

Содержание GrainVac VR12





































































































Результаты поиска

Содержание GrainVac VR12

Отзывы:

Похожие инструкции для GrainVac VR12

Бренды по названию

Популярные бренды

Rem GrainVac VR12, Руководство по эксплуатации

Результаты поиска

Содержание GrainVac VR12

Отзывы:

Похожие инструкции для GrainVac VR12

Бренды по названию

Популярные бренды