manualshive.com logo in svg

Regulus SRS3 E, Инструкция по установке, подключению и эксплуатации

Поделиться
Скачать
Regulus SRS3 E Скачать руководство пользователя страница 23

23

This function enables to release excess heat from the storage tank consi-

derately and without solar fluid overheating, via piping and collectors into 

the ambient air. It is recommended to keep activated.

Protection against pump seizing by regular short running of a pump or a valve. Seizing may 

occur after longer inactivity of valves or pumps. If the seizing protection is activated, the contro-

ller switches the relay in question and the connected solar consumer on every day at 12:00 or 

weekly on Sundays at 12:00 (setting “weekly”) for 5 seconds in order to prevent the pump and/

or the valve from sticking after an extended stationary period.

A two-stage frost protection function is available. In stage 1 the controller switches 

the pump on for 1 minute every hour if the collector temperature drops below the set 

value “

Frost level 1

”. If the collector temperature drops further to the set value “

Frost  

level 2

”, the controller switches the pump on continuously. If the collector temperature 

then exceeds the value “

Frost level 2

” by 2 °C, then the pump switches off again.

5.4. - Frost protection

Protective functions

Protective functions

At the end of a sunny day the temperature in a storage tank may easily reach high 

values. In order to prevent further temperature increase the next day, excess energy 

can be released into the air via collectors under cloudy conditions or after sunset. If 

the temperature in the storage tank exceeds the value “

Recool Tsetpoint

” and the 

collector is at least by 20 °C cooler than the storage tank, the solar pump starts. The 

storage tank is then cooled down until the “

Recool Tsetpoint

” is reached. In systems 

with two storage tanks the setting applies to both the storage tanks.

This function enables to release excess heat from the storage tank con-

siderately and without solar fluid overheating, via piping and collectors 

into the ambient air. It is recommended to keep activated.

5.5. - Seizing protection

If this temperature is exceeded at the collector sensor when the solar pump is on, a 

warning or error message is triggered. A warning message is shown on the display.

5.3. - Recooling

5.6. - Collector alarm

   Caution

   Caution

Содержание SRS3 E

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды