Regency P33LPG3-R Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 48

background image

Regency

®

P33 Gas Log Fireplace

6

INSTALLATION

CHECKLIST

1)

Locate appliance. Refer to the following
sections:

a)

Locating

Your

Fireplace

b)

Clearances

c)

Combustible

Mantels

d) Framing & Finishing

e)

Flueing

2)

Assemble Top Facing Support and Side
Nailing Strips, "Unit Assembly Prior to
Installatio" section. (NOTE: must be done
before installing unit into fi replace.)

3)

Install flue, see details on "Flueing"
sections.

4)

Make gas and electrical connections. Test

the pilot. Must be as per diagram. "Pilot
Adjustment" section. Convert to LPG if
desired, "Conversion from NG to LPG"
section.

5)

Install standard and optional features. Refer

to the following sections where applicable:

a. Brick Panels

b. Log Set

c. Flush Door

d. Double Screen Door

e. Bay Door

f.

Louvers

g. Wall Switch

h.

Wall

Thermostat

6)

Final

check.

Before leaving this unit with the customer,
the installer must ensure that the appliance is
fi ring correctly and

operation fully explained

to customer

.

This includes:

1)

Clocking the appliance to ensure the correct

fi ring rate (rate noted on label) after burning
appliance for 15 minutes.

2)

If required, adjusting the primary air to ensure

that the fl ame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.

Diagram 1

INSTALLATION

LOCATING YOUR

FIREPLACE

1)

When selecting a location for your fi replace,

ensure that the clearances outlined on this
page are met.

2)

Provide adequate clearances for servic-

ing.

3)

The appliance must be installed on a fl at,

solid, continuous surface (e.g. wood, metal,
concrete). This may be the fl oor, or raised up
on a platform to enhance its visual impact.
If the appliance is going to be installed
on carpeting, combustible linoleum tile or
other combustible material other than wood
fl ooring, the appliance must be installed on a
metal or wood panel extending the full width
and depth of the appliance.

UNIT DIMENSIONS

4)

The P33 can be installed in a recessed

position or framed out into the room as in
A, B, C, D. See Diagram 1.

5)

This appliance is Listed for bedroom

installations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.

6)

The P33 Direct Flue Gas Fireplace is ap-

proved for alcove installations, which meet
the clearances listed on the next page.

7)

We recommend that you plan your installation
on paper using exact measurements for
clearances and fl oor protection before
actually installing this appliance. Have a
qualifi ed inspector, dealer, or installer review
your plans before installation.

Note: For fl ue terminations see "Exterior Flue

Termination Locations" section.

A)

Flat on Wall

B)

Flat on Wall Corner

C)

Recessed into Wall/Alcove

D)

Corner

HEATWAVE

DUCT SYSTEM

OPTION KIT

#946-556

The

HeatWave

Air Duct Kit increases the

effectiveness of your fi replace by dispersing
warm air from the fi replace to remote locations in
the same room or other rooms in your home.

Up to two kits may be installed on the fi replace.

Please Note:

Only 1 HeatWave kit may be

operated at one time. This includes the internal
blower option as well.

33"(838mm)

33"(838mm)

23"(584mm)

12-3/4"(324mm)

29"(737mm)

28-1/2"(724

mm)

31-1/2"(800mm)

«
...
4
5
6
7
8
...
»

Содержание P33LPG3-R

















































Отзывы:

Нет отзывов

Похожие инструкции для P33LPG3-R

Бренд: Quadra-Fire Страницы: 28

Бренд: Wamsler Страницы: 82

Бренд: Napoleon Страницы: 56

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 40

Бренд: Napoleon Страницы: 16

Castlemore GDS26N

Бренд: Napoleon Страницы: 32

Бренд: Napoleon Страницы: 28

Бренд: Napoleon Страницы: 64

Бренд: Napoleon Страницы: 34

Бренд: Napoleon Страницы: 2

Ascent Linear Series

Бренд: Napoleon Страницы: 128

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 132

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 24

Бренд: Napoleon Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды