Regency P33LPG3-R Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 48

background image

Regency

®

P33 Gas Log Fireplace

7

COMBUSTIBLE MANTELS

INSTALLATION

WARNING

Fire hazard is an extreme risk if

these clearances are not ahered to.

Clearances for Bay or Flush Front

Because of the extreme heat this fi replace emits, the mantel clearances are critical.

Combustible mantel clearances from top of unit are shown in the diagram below.

Note: A non-combustible mantel may be installed at a lower height if the framing

is made of metal studs covered with a non-combustible board.

MANTEL LEG CLEARANCES

Combustible mantel leg clearances as per diagram below:

This drawing is to scale at 1:6 (one inch = 6 inches). Mantel can be installed anywhere in shaded
area or higher using the above scale.

Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the

paint may discolour.

CLEARANCES

The clearances listed below are Minimum distances
unless otherwise stated:

A major cause of chimney related fi res is failure
to maintain required clearances (air space)
to combustible materials. It is of the greatest
importance that this fi replace and fl ue system
be installed only in accordance with these
instructions.

Clearance to Combustibles from:
Back

0"

(0mm)

Side

0"

(0mm)

Floor

0" (0mm)

NOTE: The minimum fl oor clearance must be main-
tained from the top surface of the carpeting, tile, etc.

Minimum Clearance from Top of Unit to:

Mantel*

min. 7" (177mm)

Ceiling

30" from top of unit (762mm)

Side Wall Clearance

Bay or Flush Front

7-1/2"

(191mm)

Minimum Flue Clearances:

2-1/2" (64mm) Horizontal Top
1-1/2" (38mm) Horizontal Side
1-1/2" (38mm) Horizontal Bottom
1-1/4" (32mm) Vertical Flue Clearance (Simpson)
1-1/2" (38mm) Vertical Flue Clearance (Flex)

Alcove Clearances:
Max. Depth

36"

(914mm)

Min. Width

48"

(1219mm)

Min. Height

59"

(1499mm)

* see mantel clearance instructions.

Maximum
1-1/2" (38mm) projection
at 2" (51mm) minimum
clearance.

The

HeatWave

Duct Kit has different

clearance and framing requirements,
check the

HeatWave

manual for details.

«
...
5
6
7
8
9
...
»

Содержание P33LPG3-R

















































Отзывы:

Нет отзывов

Похожие инструкции для P33LPG3-R

Бренд: Valor Страницы: 4

Бренд: Four Seasons Courtyard Страницы: 12

Бренд: HAMPTON BAY Страницы: 19

Бренд: Empire Comfort Systems Страницы: 13

Бренд: CC Products Страницы: 7

Бренд: Jøtul Страницы: 52

Бренд: Lopi Страницы: 3

Бренд: crystal fires Страницы: 26

Бренд: Piazzetta Страницы: 48

Бренд: Contura Страницы: 36

Бренд: Dru Страницы: 24

FIREPOD universal

Бренд: ADVANCE Easy Moving Страницы: 24

Бренд: Vanguard Страницы: 40

Бренд: ROOMS TO GO Страницы: 11

Haliburton GDS28P

Бренд: Napoleon Страницы: 48

Oakville Series

Бренд: Napoleon Страницы: 76

Бренд: Napoleon Страницы: 10

OUTDOOR LIVING REDEFINED OUTDOOR FIREPIT

Бренд: California Outdoor Concepts Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды