Regency Horizon HZ30E-LP1 Скачать руководство пользователя страница 45

Страница: 45 / 64

Regency Horizon™ HZ30E-1 Gas Fireplace

INSTALLATION

Do not remove the screw just left of the pilot shield - this secures the

valve tray in position.

13)

Attach the green ground wire to the ground lug - located in the lower

left back corner of the unit.

14)

Reposition the valve access plate - before securing with 17 screws

(see step 8 for screw locations) - slide in the thermodisc to the clip on

the bottom of the access plate. Attach the 2 wires from the fan to the

thermodisc as shown below.

15)

Plug the fan into the receptacle located in the lower right front corner at

the base of the unit.

16)

To remove the fan - reverse steps.

10)

Manoeuvre the fan into position in the lower right corner at the base

of the unit.

11)

Attach the thermodisc wires - (by sliding them on) to the fan as shown

below.

12)

Secure the fan to the base of the unit with 2 screws.

TO REMOVE THE FAN

Turn the power off.

Reverse the above instructions.

Maintenance:

The sealed bearings are lubricated, there is no need to lu-

bricate them further. (Extra lubricant will cause more lint and dust buildup

- causing the bearings to prematurely fail).

Regular cleaning and vacuuming of the fan area will add to the life of the

motor.

IMPORTANT:

These fans collect a lot of dust from within your home. Ensure you

maintain these fan motors on a regular basis by vacuuming

the fan blades and housing using a soft brush nozzle.

Содержание Horizon HZ30E-LP1

































































Результаты поиска

Содержание Horizon HZ30E-LP1

Отзывы:

Похожие инструкции для Horizon HZ30E-LP1

Бренды по названию

Популярные бренды

Regency Horizon HZ30E-LP1, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ30E-LP1

Отзывы:

Похожие инструкции для Horizon HZ30E-LP1

Бренды по названию

Популярные бренды