Regency Horizon HZ30E-LP1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 64

background image

12

Regency Horizon™ HZ30E-1 Gas Fireplace

INSTALLATION

UNIT ASSEMBLY

PRIOR TO

INSTALLATION

The nailing Strips must be correctly positioned and attached before unit is
slid into position.

NAILING STRIPS

The nailing strips come attached to the unit. There is 1 plate on each side, 1
on the top, and one on the bottom that can be folded out as required.
The top and side nailing strips are secured to the framing. The bottom
nailing strip is secured to the unfi nished fl oor - if installing the unit directly
on the fl oor.

IMPORTANT NOTE

Framing depth measurement is noted with
the nailing strips set as far forward on the
fi rebox as possible. The nailing strips can
be adjusted back up to 1-1/2” to allow for
varying thicknesses in non-combustible
material & wall fi nishes.

Nailing Strips

INSTALLATION ACCESS PANEL

The unit is equipped with a removable access panel for pre-fi nish installation
of optional components - this panel is located on the lower front face.

1)

Remove 2 screws to remove access panel.

2)

Easier access to gas connection with panel removed.

3)

Install any optional components with access panel removed.

4)

Reinstall access panel with 2 screws - prior to installing any facing material

Note:

Access panel is no longer usable once facing material installed.

Installation Access Panel

Screw Locations

«
...
10
11
12
13
14
...
»

Содержание Horizon HZ30E-LP1

































































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ30E-LP1

OUTLAND LIVING FIRECUBE

Бренд: FMI Страницы: 12

DRI3030TEN-CONTF-BLK

Бренд: Superior Fireplaces Страницы: 2

Бренд: Looft Industries Страницы: 16

Бренд: Mainstays Страницы: 37

Бренд: Empire Comfort Systems Страницы: 28

MSS136144273001

Бренд: Mainstays Страницы: 16

Бренд: Firesense Страницы: 18

Бренд: Essence Страницы: 3

Бренд: Desa Страницы: 36

Бренд: Yosemite Страницы: 15

Бренд: Majestic Страницы: 24

Flush Wood Large Hybrid-Fyre

Бренд: Lopi Страницы: 13

Бренд: Panadero Страницы: 32

LANGSTON OFW821RC

Бренд: pleasant hearth Страницы: 24

Бренд: pleasant hearth Страницы: 15

Бренд: pleasant hearth Страницы: 4

Бренд: pleasant hearth Страницы: 33

Бренд: Kingsman Fireplaces Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды