manualshive.com logo in svg

Regency Horizon HZ30E-LP1, Инструкция для владельца и по установке

Пожалуйста, скачайте бесплатно Руководство пользователя и установки для продукта "Regency Horizon HZ30E-LP1" с нашего вебсайта manualshive.com. Этот мануал поможет вам разобраться с функциями этого продукта. Не забудьте загрузить его с manualshive.com прямо сейчас!

Поделиться
Скачать
background image

4

Regency Horizon HZ30E Gas Fireplace

TABLE OF CONTENTS

Copy of Safety Decal .....................................................5

REQUIREMENTS

MA Code - CO Detector.................................................6
(for the State of Massachusetts only) ............................6
Unit Dimensions ............................................................7
Faceplate and door frame Dimensions..........................7

INSTALLATION

Important Message   ......................................................8
Before You Start ............................................................8
General Safety Information............................................8
Installation Checklist ......................................................9
Locating Your Gas Fireplace .........................................9
Clearances ..................................................................10
Mantel Clearances....................................................... 11
Mantel Leg Clearances................................................ 11
Unit Assembly Prior To Installation ..............................12

Nailing Strips ........................................................12
Installation Access panel .....................................12

Wall mount On / Off Switch and receiver installation ...13
Required for all installations - including profl ame remote 
controls ........................................................................13
GT remote Installation .................................................13
Framing Dimensions....................................................14
Framing & Finishing.....................................................15
Framing & Finishing.....................................................16
Non-Combustible Requirements .................................16
Exterior Vent Termination Requirements .....................17
4” x 6-5/8” Rigid Pipe Cross Reference Chart only .....18
Vent Restrictor Position ...............................................20
Venting Introduction .....................................................21
Venting Arrangement for Horizontal Terminations .......21
Horizontal Terminations  Flex Vent 4" x 6-7/8" .............22
Horizontal terminations ................................................23
Rigid Pipe 4" x 6-5/8" ...................................................23
Horizontal Terminations ...............................................24
Rigid Pipe 4" x 6-5/8" ...................................................24
Venting Arrangement for Vertical Terminations ............27
Venting Arrangements - Vertical Terminations  ............28
Vertical Termination with Co-Linear Flex System ........29
Vertical Terminations ...................................................30
Rigid Pipe 4" x 6-5/8" ...................................................30
Unit Installation with Horizontal Termination  ...............32
4" x 6-5/8" venting .......................................................32
Unit Installation with Horizontal Termination  ...............33
Unit installation with Vertical Termination ....................34
4" x 6-5/8" venting .......................................................34
High Elevation .............................................................35
Gas Line Installation ....................................................35
Pilot Adjustment ...........................................................35
Gas Pipe Pressure Testing ..........................................35

880 S.I.T. Valve Description .........................................35
Aeration Adjustment ....................................................35
Wiring Diagram ............................................................36
Profl ame Remote system GTMF .................................36
AC power adaptor installation (for surefi re systems) ...37
Profl ame remote system GTMF with optional fan .......38
Optional fan Wiring Diagram  ......................................39
Without ProFlame GTMF system ................................39
Optional Remote Control .............................................40
 Receiver Wall Switch ..................................................40
Optional wall thermostat installation ............................41
GTMF remote installation ............................................42
Optional fan Installation ...............................................44
Refl ective Panel Installation ........................................46
Glass Crystals or optional stones ................................47
Installation On Burner ..................................................47
Optional log set Installation .........................................49
Glass door Installation .................................................52
4 pc. Faceplate Installation ..........................................53
Outer and inner door frame Installation .......................54

OPERATING INSTRUCTIONS

Operating Instructions .................................................55
First Fire ......................................................................55
Lighting Procedure ......................................................55
Shutdown Procedure ...................................................55
Normal Operating Sounds of Gas Appliances .............55
Copy of Lighting Plate Instructions ..............................56
Maintenance Instructions.............................................57
Glass Gasket ...............................................................57
Glass Door...................................................................57

Glass Replacement .............................................57

General Vent Maintenance ..........................................57
Valve assembly Replacement .....................................58

PARTS LIST

Main Assembly ............................................................60
Accessories .................................................................61

WARRANTY

The Warranty: Limited Lifetime  ...................................63

Содержание Horizon HZ30E-LP1

































































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ30E-LP1

IHP PCBM-325 Manual preview
PCBM-325
Бренд: IHP Страницы: 8
Pacific energy Series A Installation Manual preview
Series A
Бренд: Pacific energy Страницы: 60
Pacific energy ESPRIT Installation And Operating Instructions Manual preview
ESPRIT
Бренд: Pacific energy Страницы: 40
Pacific energy SUPER INSERT DESIGN-E SPNE Operating Instructions Manual preview
SUPER INSERT DESIGN-E SPNE
Бренд: Pacific energy Страницы: 24
Valor Retrofire RF24XBN Installation Manual And User'S Manual preview
Retrofire RF24XBN
Бренд: Valor Страницы: 32
Restoration Hardware 26100040 Assembly Instructions preview
26100040
Бренд: Restoration Hardware Страницы: 4
California Outdoor Concepts Carmel Chat Product Information Manual preview
Carmel Chat
Бренд: California Outdoor Concepts Страницы: 8
Empire Comfort Systems P)-5 Installation Instructions Manual preview
P)-5
Бренд: Empire Comfort Systems Страницы: 60
Lamborghini Caloreclima 90 PM/M-E Use Manual preview
90 PM/M-E
Бренд: Lamborghini Caloreclima Страницы: 40
Flavel REGENT FRLC EN Series Installation And Maintenance Instructions Manual preview
REGENT FRLC EN Series
Бренд: Flavel Страницы: 31
OVE Brooks 15PFP-BROO24-CHDRY Assembly Instructions preview
Brooks 15PFP-BROO24-CHDRY
Бренд: OVE Страницы: 4
Landmann Brooke Assembly And Use Instructions preview
Brooke
Бренд: Landmann Страницы: 6
Dimplex EMP-075-W Install Manual preview
EMP-075-W
Бренд: Dimplex Страницы: 2
Capital fireplaces TF-1561ERA Installation Manual preview
TF-1561ERA
Бренд: Capital fireplaces Страницы: 4
Capital fireplaces PHANTASY TF-1561ERA Instruction Manual preview
PHANTASY TF-1561ERA
Бренд: Capital fireplaces Страницы: 8
pleasant hearth MARTIN OFW165S User Manual preview
MARTIN OFW165S
Бренд: pleasant hearth Страницы: 12
GlammFire Fogly Manual preview
Fogly
Бренд: GlammFire Страницы: 13
GlammFire KIT Glamm H3D 700 Manual preview
KIT Glamm H3D 700
Бренд: GlammFire Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды