Regency Horizon HZ30E-LP1 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 64

background image

36

Regency Horizon™ HZ30E-1 Gas Fireplace

INSTALLATION

WIRING DIAGRAM

This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat will
continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation.

(Do not cut the ground terminal off under any circumstances.)

NOTE: Even if the fan is not purchased with the unit, it is still a good idea to bring power to the receptacle box (provided with the unit) in case the

fan is installed at a later date.

Proflame System
Configuration
886 GTMF
Wire Diagram

0.880.001

Profl ame System
Confi guration
880 ON/OFF
Illustrated wire diagram

0.584.907

PROFLAME REMOTE SYSTEM GTMF

SureFire™ Switch

CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can
cause improper and dangerous operation.

Caution: Ensure that the wires do not touch any
hot surfaces and are away from sharp edges.

Note:

4 AA batteries must be installed to operate

the burner switch.
Do not use a 9 volt battery.

IMPORTANT:

If the optional remote control is used, the AA batteries normally installed into the battery holder must be removed. The AA batteries in the

receiver now operate the unit. Having AA batteries in both the battery holder and receiver will damage the gas valve.

«
...
34
35
36
37
38
...
»

Содержание Horizon HZ30E-LP1

































































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ30E-LP1

Бренд: Quadra-Fire Страницы: 28

Бренд: Majestic Страницы: 56

Бренд: IHP Страницы: 12

Бренд: WANDERS Страницы: 68

Бренд: WANDERS Страницы: 68

Бренд: Ortech Страницы: 9

OUTLAND LIVING FIRECUBE

Бренд: FMI Страницы: 12

Бренд: HAMPTON BAY Страницы: 36

Бренд: Be Modern Страницы: 8

Бренд: Lamborghini Caloreclima Страницы: 40

Бренд: Pacific energy Страницы: 24

Бренд: Valor Страницы: 6

Бренд: barbas Страницы: 84

PORTRAIT BSK541

Бренд: Valor Страницы: 2

Duraflame 18IRM9984

Бренд: Twin-Star International Страницы: 26

WM -FM L-26-3223-STL

Бренд: Sierra Flame Страницы: 23

Бренд: Comfort Glow Страницы: 38

Бренд: Monessen Hearth Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды