Regency Horizon HZ30E-LP1 Скачать руководство пользователя страница 41

Страница: 41 / 64

Regency Horizon™ HZ30E-1 Gas Fireplace

INSTALLATION

CAUTION

Do not wire millivolt

Thermostat wires

to 120V wire.

Thermostat Wire Table

Recommended Maximum Lead Length

(Two-Wire) When Using Wall

Thermostat (CP-2 System)

Wire Size

Max. Length

14 GA.

50 Ft.

16 GA.

32 Ft.

18 GA.

20 Ft.

20 GA.

12 Ft.

22 GA.

9 Ft.

OPTIONAL WALL THERMOSTAT INSTALLATION

This installation must be completed during initial install with the front access panel removed.

A wall thermostat may be installed if desired.
Recommended: Mount thermostat beside unit receiver.

Run wires from thermostat into the unit using the appropriate wire gauge - see chart below.

Connect one thermostat lead to female connector, using male spade con-

nector - see pic below.

Connect one thermostat lead to male connector using female spade con-

nector - see pic below.

When complete turn remote receiver to the ON position.
Unit will now operate using the wall thermostat.

Remove the green wire marked (TH) at the white connector - shown

below.

Disconnect TH wire

Содержание Horizon HZ30E-LP1

































































Результаты поиска

Содержание Horizon HZ30E-LP1

Отзывы:

Похожие инструкции для Horizon HZ30E-LP1

Бренды по названию

Популярные бренды

Regency Horizon HZ30E-LP1, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ30E-LP1

Отзывы:

Похожие инструкции для Horizon HZ30E-LP1

Бренды по названию

Популярные бренды