Regency horizon HRI6E Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 60

background image

LRI6E / HRI6E Direct Vent Gas Insert

|

21

|

21

installation

GLASS CRYSTAL / OPTIONAL STONE INSTALLATION

Spread the Glass Crystals or Stones evenly over the burner. Ensure the crystals/stones do not overlap excessively as this will affect the flame pattern.

IMPORTANT NOTE:

Only the supplied approved Glass Crystals and Stones are to be used with these fireplaces. Use of any other type of glass crystals or stones can alter the
unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty.
When using Ceramic Spa/Volcanic Stones

DO NOT

cover burner ports or pilot light that lead to pilot flame.

OPTIONAL PEBBLES / GLASS CRYSTAL INSTALLATION FOR FIREBOX BASE (AROUND BURNER)

Firebox (Around Burner) Packages

Unit

Glass Crystals

Pebbles

HRI6E

6 lbs burner

2 packages (use 5 bags pebbles)

There are 2 optional packages to choose from to cover the firebox base:

1)

Natural River Pebbles

2)

Glass Crystals (4 colors available)

Spread the pebbles / crystals evenly on the exposed base of the firebox. Pebbles are

NOT

to be placed anywhere on the burner or over top of the Glass

Crystals or optional Stones.

IMPORTANT NOTE:

Only the supplied and approved pebbles / glass crystals are to be used with these fireplaces. Use of any other type of pebbles, glass
crystals or other material can create a danger and will void the warranty.

BURNER PACKAGES

Unit

*Glass Crystals Fire Beads

Stones - Spa / Ceramic / Volcanic

HRI6E

11 lbs [6 lbs 5
lbs firebox]

11 lbs [6 lbs 5
lbs firebox]

10 lb Glass + 1 package (70 Spa Stones) / 8 lb Glass + 40 Volcanic Stones
8 lb Glass + 30 Ceramic Stones
11 lbs beads + 70 spa stones/40 volcanic stones/30 ceramic stones

NOTE:

*

Glass Crystals are not supplied with the unit. Must purchase separately - see quantities above.

Note: 1 Spa stone package contains 70 stones.

DO NOT block pilot area with glass crystals

Glass Crystals shown on Burner and Firebox Floor

«
...
19
20
21
22
23
...
»

Содержание horizon HRI6E





























































Отзывы:

Нет отзывов

Похожие инструкции для horizon HRI6E

Бренд: baltur Страницы: 76

Бренд: Paloform Страницы: 15

Бренд: barbas Страницы: 100

Бренд: KENT Страницы: 2

Бренд: Travis Industries Страницы: 2

Бренд: Landmann Страницы: 8

Бренд: Heat & Glo Страницы: 33

Бренд: Style selections Страницы: 24

Бренд: RealFlame Страницы: 27

Бренд: Sonnenkonig Страницы: 48

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 2

Victorian V36EN Series

Бренд: Desa Страницы: 38

Бренд: hoxter Страницы: 68

Бренд: Nibe Страницы: 4

Бренд: Red Fire Страницы: 17

Electric Fireplace

Бренд: Electralog Страницы: 14

Бренд: Blumfeldt Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды