Regency horizon HRI6E Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 60

background image

44

|

LRI6E / HRI6E Direct Vent Gas Insert

|

44

maintenance

GLASS CRYSTAL BURNER REMOVAL / INSTALLATION (HRI6E)

Care must be taken when installing the burner into the firebox.

Do not damage, knock or scrap the pilot assembly.

The flame sensor and ignition lead are fragile and can be damaged

easily.

1)

If already installed, remove glass crystals and ceramic spa stones.

2)

Remove filler sections from right and left sides of burner. Discard filler sec-

tion if enamel panels are to be installed - see below.

1)

Lift the burner assembly with both hands. Point the mixing tube towards

the rear of the firebox. Lean the rear of the burner assembly downward.
Partially lift the burner assembly so that the mixing tube will then slide
into the air shutter.

2)

Lower the front edge of the burner assembly so that the burner front

mounting tab rests on the burner mounting bracket left and right, near
the front of the firebox. These tabs will not line up unless the mixing tube
is inside the air shutter at the rear of the firebox.

Glass / Media Burner

* Side view cut-through *

Burner

Pilot Cover

Burner Screen

Glass / Media

Tray

Fill Glass / Media

to this level

Mixing Tube

Disconnect unit from gas supply and allow unit to cool before removing

burner.

Filler section

GLASS BURNER REMOVAL

GLASS BURNER INSTALL

3)

Place the Burner Cover Screen over the Burner Ports. Place the Pilot

Cover over the rear gap between the Burner and the Media Tray. This will
sit around the Pilot Provision.

4)

Distribute the glass crystals throughout the Media Tray. The media should

be level with the side of the Media Tray.

*

* Do not to install glass or other media over or in front of the Pilot

Provision as shown.

Burner

Burner Screen

Mixing Tube

Air Shutter

Burner Mounting Brackets

Important:

Do not to install glass or
other media in this area, as
this will block the path of the
pilot to the burner.

3)

Remove the 2 screws as shown. Lift the burner with both hands.

4)

Pull gently upwards and outwards to the front of the firebox.

5)

Continue onto burner installation.

«
...
42
43
44
45
46
...
»

Содержание horizon HRI6E





























































Отзывы:

Нет отзывов

Похожие инструкции для horizon HRI6E

Бренд: HAMPTONBAY Страницы: 30

Imperial Carousel

Бренд: Malm Fireplaces Страницы: 8

Бренд: Majestic Страницы: 81

Бренд: Jensen Страницы: 45

Бренд: SAN HIMA Страницы: 7

Wall Mantel with Base and Trim WD26CPA

Бренд: Desa Страницы: 4

Бренд: Napoleon Страницы: 40

Бренд: Heta Страницы: 20

Бренд: HAMPTON BAY Страницы: 9

Бренд: HAMPTON BAY Страницы: 9

Бренд: Desa Страницы: 20

Бренд: Dogberry Collections Страницы: 2

Бренд: Heat & Glo Страницы: 30

Бренд: AFLAMO Страницы: 36

Бренд: Megamaster Страницы: 15

Бренд: Totem Страницы: 23

Бренд: Vermont Castings Страницы: 24

Бренд: KFD Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды