LRI6E / HRI6E Direct Vent Gas Insert
|
11
|
11
installation
A
B
C
MATERIALS REQUIRED
A 120 Volt AC power cord is hooked up to operate the fan and operate the gas valve when batteries
are not installed in the receiver. Plug the 3 wire cord into a suitable receptacle.
Do not cut the
ground terminal off under any circumstances.
When connected with 120 volts, the appliance must
be electrically grounded in accordance with local codes, current version of CSA C22.1 (in Canada)
or in the absence of local codes, with the National Electrical Code ANSI/NFPA 70-1987
INSTALLATION
CHECKLIST
Before installing vent system ensure that the damper
plate is open and secure to prevent the damper plate
from falling down and crushing the liner.
The Regency Gas Insert is installed as listed.
1)
Check all clearances to combustibles, (Refer to
sections "Minimum Fireplace Dimensions and
Clearances to Combustibles)
2)
Make the gas connection. (Refer to section "Gas
Connection") Gas connection is on the left side
of the appliance.
3)
Install the two flue liners (intake and exhaust)
to the sliding connector plate. (Refer to section
"Flue Liner Installation.")
4)
Slide the unit half way into the fireplace.
5)
Pull the vent connector plate through the
brackets and fasten to the front plate. Refer to
section "Flue Liner Installation.")
6)
Slide the unit fully into the fireplace. Level if
necessary.
7)
Hook up 120 volt AC power cord into a suitable
receptacle. Optional: Install 4 batteries in
receiver. Batteries only serve as back up if
power is lost within the home.
8)
Plug the 3 wire cord into a suitable
receptacle. The 3 wire cord is located on the
right side of the unit.
9)
Code remote control. See Remote Control
Instruction Manual.
10)
Test gas pressure (Refer to section "Gas Pipe
Pressure Testing"). Check aeration system
(Refer to section "Gas Insert Aeration System").
11)
Install standard and optional features. Refer to
the following sections:
a. Brick Panels
b. Enamel Panels
c. Log Set
d. Glass Crystals
e. Spa stones
f. Standard Vignette Faceplate
g. 4 sided Vignette Faceplate
h. Backing Plate
i. Inlay
j. Spacer
k. Hearth Trim
12)
Final check:
Before leaving this unit with the
customer, the installer must ensure that the
appliance is firing correctly. This includes:
a)
Clocking the appliance to ensure the correct
¿ULQJUDWH
b)
Adjusting the primary air, if required, to
HQVXUHWKDWWKHÀDPHGRHVQRWFDUERQ6HH
"Gas Insert Aeration System" section.
c)
Ensuring that the appliance is venting
correctly.
MINIMUM FIREPLACE DIMENSIONS
The minimum fireplace clearances & dimensions for the Regency gas insert are shown in the following
diagrams:
Max Lentil
Bar Depth
A
Height
B
Depth
C
Width
(rear)
D
Width
(front)
E
Width
F
Front Depth
Prior to Taper
G
Vignette
Faceplate
12.5"
24"
19.5"
25"
34"
37"
4-3/4"
Vignette
Faceplate
w/ spacer
10"
24"
16.75"
25"
34"
35-3/8"
2-1/4"
Содержание horizon HRI6E
