Regency horizon HRI6E Скачать руководство пользователя страница 32

Страница: 32 / 60

LRI6E / HRI6E Direct Vent Gas Insert

installation

VIGNETTE FACEPLATE WITH SAFETY SCREEN INSTALLATION

919-660

05.18.16

VIGNETTE FACEPLATE

WRROWLS

1. Pop out tab on right side (facing front) of outer faceplate and place

grommet in opening to route power cord.

2. Install the outer faceplate and secure with 5 screws for the L/HRI4E

and L/HRI6E as shown.

Note: 4 corner screws can be installed on the unit loosely as the hole

on the outer faceplate are keyholes.

Route power cord on right side between the inner and outer profile of

faceplate. Use a grommet and wire clip to secure.

3. Install the Vignette faceplate by hooking the flange over the hanger

as shown.

VIGNETTE FACEPLATE W/ SAFETY SCREEN INSTALLATION

Final Install

Note:

Shown with Optional Hearth Trim

4. Ensure finger prints or smudges are removed from the faceplate

before the first firing.

NOTE:

Pull the bottom of the Vignette faceplate towards you to access

the remote receiver.

Power Cord

Location

Pop out tab on right side

of outer faceplate

Black Chrome Handling Instructions

$OOKDQGDQG¿QJHUPDUNV

MUST

EHFOHDQHGRIIZLWKDVRIWFORWK8VHDQDPPRQLDEDVHGFOHDQHULHJODVVFOHDQHUWRUHPRYHDQ\

¿QJHUSULQWVEHIRUHDSSO\LQJKHDWWRWKHXQLW8VHVXSSOLHGJORYHVZKHQLQVWDOOLQJ%ODFN&KURPH)DFHSODWHV

Failure to do this will result in burn stains on panels which you will be unable to remove.

1RWSURWHFWHGE\SURGXFWZDUUDQW\

WRROWLS

Содержание horizon HRI6E





























































Результаты поиска

Содержание horizon HRI6E

Отзывы:

Похожие инструкции для horizon HRI6E

Бренды по названию

Популярные бренды

Regency horizon HRI6E, Инструкция для владельца и по установке

Результаты поиска

Содержание horizon HRI6E

Отзывы:

Похожие инструкции для horizon HRI6E

Бренды по названию

Популярные бренды