Regency Energy E18E Скачать руководство пользователя страница 65

Страница: 65 / 104

Regency

E18E-11 Gas Fireplace Insert

| 65

installation

AC POWER ADAPTOR INSTALLATION (FOR SUREFIRE SYSTEMS)

An AC power adaptor MUST be installed as a constant power source for the SureFire system.

IMPORTANT: Do not use the 4-AA batteries in the SureFire receiver.

INSTALL AC ADAPTOR WITH SUREFIRE WALL SWITCH/WALL THERMOSTAT ONLY - (WITHOUT REMOTE)

INSTALL AC ADAPTOR WITH SUREFIRE PROFLAME REMOTE

1. Locate “DC Supply” tag on wire harness (located in the unit).

2. Connect the male end from AC adaptor to the female end
tagged “DC Supply” on wiring harness in unit.

2. Locate FCM - COM connector labeled on the Remote wire harness.

3. Attach female end of DC supply wire (red/black) from valve wiring

harness located on unit to the male FCM-COM supply wire (red/black)
from remote control wiring harness - be careful not to damage ends.
This only fits one way. Do Not Force in wrong way.

3. Plug AC adaptor into 120V power cord located inside the gas fireplace

firebox).

4. Neatly tuck any loose AC Power Adaptor wires underneath / inside

the appliance.

Note: Ensure that wires do not touch the underside of the firebox

(keep wires away from the heat as much as possible).

FCM - COM

AC adaptor

wire adaptor

1. Connect the male end of the AC adaptor (from unit) to the female end

of the wire adaptor (supplied with optional remote) together as shown.

AC adaptor

Wire adaptor

FCM - COM

4. Plug AC adaptor into 120V wall outlet (or into 120V power cord located

inside the gas fireplace firebox).

5. Neatly tuck any loose AC Power Adaptor wires underneath / inside

the appliance.

Note:

This should only be plugged in when unit is fully installed and

ready for use.

Note:

Ensure that wires do not touch the underside of the firebox (keep
wires away from the heat as much as possible).

Содержание Energy E18E









































































































Результаты поиска

Содержание Energy E18E

Отзывы:

Похожие инструкции для Energy E18E

Бренды по названию

Популярные бренды

Regency Energy E18E, Инструкция для владельца и по установке

Результаты поиска

Содержание Energy E18E

Отзывы:

Похожие инструкции для Energy E18E

Бренды по названию

Популярные бренды