Regency Energy E18E Скачать руководство пользователя страница 66

Страница: 66 / 104

66 |

Regency

E18E-11 Gas Fireplace Insert

installation

GTM REMOTE INSTALLATION

6. Remove the hi/lo knob if installed by removing 2 screws as
shown below.

GTM REMOTE INSTALLATION

5. See AC adaptor install instructions in this manual.

7. Install the stepper motor in the same location the hi/lo knob was
removed from - with 2 screws as shown below.

8. Plug wiring harness into back of receiver as shown below.

9. Plug the stepper motor into the ‘motor wire as shown below.

Motor Wire

919-803

06.26.17

1. Shut off the gas supply and disconnect all power to the unit.

2. Remove the control cover.

3. Identify short (3” long) brown wire that is attached to the white wire

coming from the DFC. Remove the 3” brown wire and discard.

White

Brown to

Green

Discard

3” brown

wire

4. Connect the Green wire from the GTM wire harness to the brown,

connect the white wire from the same harness to white.

E18E

Содержание Energy E18E









































































































Результаты поиска

Содержание Energy E18E

Отзывы:

Похожие инструкции для Energy E18E

Бренды по названию

Популярные бренды

Regency Energy E18E, Инструкция для владельца и по установке

Результаты поиска

Содержание Energy E18E

Отзывы:

Похожие инструкции для Energy E18E

Бренды по названию

Популярные бренды