Regency Energy E18E Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 104

background image

Regency

®

E18E-11 Gas Fireplace Insert

| 25

installation

1. Locate model on existing ZC box - locate corresponding section in

this manual.

2. Make necessary alteration to the ZC firebox as per manual.

3. Separate inner and outer fire box (see procedure in manual).

4. Remove flue adaptor for outer firebox.

5. Make necessary adjustment to flue adapter mounting plate as per

manual.

6. Cut flex to required length and secure to top plate using 3 screws

and washers.

7. Secure top plate flue adapter to ZC box.

8. Secure flue adapter to flex using 3 screws/washers.

9. Slide outer firebox into place, be sure flue adapter mounting screw

doesn't hold unit up on installation.

10. Adjust left and right side legs on outer shell (depends on ZC box it is

being intalled in) - See details in manual.

11. Measure and align outer firebox as per manual, secure each corner

using self tapping screws.

•  Nibbler
•  Oscillating tool / metal blades
•  Tin snips
•  Uni Bit/Step Drill
•  Black high temp paint
•  Drill/ ¼” bit – Phillips bit
•  Measuring tape
•  Level
•  Sharpie
•  Shop vacuum

TOOLS REQUIRED (SUGGESTED)

Nibbler

Oscillating tool

Optional:

•  Plasma cutter
•  Fibre drop sheet
•  Fire extinguisher

12. Install inner firebox into outer firebox, ensure draft hood bottom

fits on top of draft hood slides, left side, right side and rear.

13. Secure inner firebox - 2 screws on top left and right side - using

existing holes.

14. Secure inner firebox on bottom inside - 2 screws on each side. Be

sure to re install panel brackets, and line up with existing holes.

15. Reinstall burner.

16. Make gas connection - check for leaks.

17. Install enamel panels.

18. Install Faceplate

19. Install Glass Crystals on burner.

20. Light pilot.

21. Install glass door.

22. Install thermostat.

REQUIRED STEPS AND PROCEDURES FOR E18E INSTALLATION

IMPORTANT : All original vent systems must be inspected for carbon/soot build up prior to installation of the E18E. The installer should

also ensure prior to installation that the existing vent system is adequate for the rated input of this appliance (21,600 BTU
NG/20,500 BTU LP).

Signs of white buildup (aldehydes) in the vent system would indicate that the appliance was not drafting properly due to
vent height, diameter of vent, excessive offsets, negative pressure, kinks, etc.

Adhere to the local gas code within your jurisdiction for vent sizing.

Any venting system that causes the Regency E18E to not function as it should is not the responsibility of the manufacturer.

«
...
23
24
25
26
27
...
»

Содержание Energy E18E









































































































Отзывы:

Нет отзывов

Похожие инструкции для Energy E18E

Бренд: Harman Страницы: 10

Бренд: Napoleon Страницы: 56

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 40

Бренд: Napoleon Страницы: 16

Castlemore GDS26N

Бренд: Napoleon Страницы: 32

Бренд: Napoleon Страницы: 28

Бренд: Napoleon Страницы: 64

Бренд: Napoleon Страницы: 34

Бренд: Napoleon Страницы: 2

Ascent Linear Series

Бренд: Napoleon Страницы: 128

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 132

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 24

Бренд: Napoleon Страницы: 31

Бренд: Napoleon Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды