background image

-

12

-

6.5 Discharging Lithium battery  

The  value  of  discharge  current  on  the  left  side  of 
screen  may  not  exceed  1C  for  maximum  safety 
and  the 

final voltage on the right should not be under 

the  voltage  level  that  is  recommended  by  the  battery 
manufacturer to avoid deep discharge.
To start discharge, press 

Start/ Enter

 key for more 

than 3 seconds.

This  shows  the  present  state  of  discharge.  To  stop 
discharging press 

Batt type/Stop

 key once.

6.6 Voltage balancing and monitoring while discharging

The charger monitors the voltage of individual cells during 'storage-mode' and 

'discharge'  of  a   Lithium  battery  pack.  It  tries  to  e q u a l  t h e   v o l t a g e   o f   e a c h   c e l l . 
For  this  feature,  the  individual  plug  of  the  battery  pack  should  be  connected  to  the 
individual port of the charger.

If the voltage of any one or more cells varies abnormally during the procedure, It 

terminates  the  process  with  an  error  message.  If  this  happens,  the  battery 
pack  contains  a  bad  cell,  or  a bad  connection. To check which cell is bad press 
the INC button at the time of  error.

The charger has detected that the voltage of one cell 
in the Lithium battery pack is too low.

In  this  case,  the  4th  cell  is  bad.  If  there  is a 
connection-break of the cable or plug, the voltage value 
may show zero.

Содержание SPIDER 1s
























Отзывы: