background image

 

P

UB

.

 

42004-472B 

 

A

UTO

-D

IAL 

T

ELEPHONE 

M

ANUAL

 

P

AGE 

22 of 33

 

f:\standard ioms - current release\42004 instr. manuals\42004-472b.doc 
01/15

 

Programming Sequences 

The programming information on the following pages explains 
the programming options.  The telephone is shipped from the 
factory with a set of default parameters that are listed in the 
Programming Table on page 29.  A “User Settings” section has 
been provided in the Programming Table for the user to record 
the selected programming parameters. 

Dialing Options 

The auto-dial telephones can be configured for either auto-dialing or ring-down operation.  Select the 
dialing option that fits your application.  The dialing options are explained in detail below. 

Auto-dialing 

The 

CALL

 push button can be programmed to call up to three unique telephone numbers.  The unique 

telephone numbers include a primary telephone number and two backup, or roll over, numbers.  In the 
event an auto-dial call cannot connect to the primary telephone number (i.e., a busy signal or no answer), 
the auto-dial telephone will automatically dial the first backup, or roll over, number.  Again, in the event 
an auto-dial call cannot connect to first back-up telephone number, the auto-dial telephone will 
automatically dial the second backup, or roll over, number (if used).  This sequence will continue until the 
auto-dial call is answered, or all numbers have been attempted (one attempt each). 

When operating in SMART mode, the number of attempts to call each programmed number can be 
increased, as required, (two attempts each, three attempts each, etc.) 

For the rollover feature to function properly in this mode, all three auto-dial memories must be 
programmed with valid telephone numbers.  The three auto-dial numbers can be the same or any 
combination of telephone numbers.  If the telephone is programmed with only one or two auto-dial 
numbers, the rollover operation will not function and the numbers will only be dialed one time. 

If an auto-dial telephone is connected to a PBX, PABX, KSU, etc., telephone system, the auto-dial 
telephone can be programmed to access outside CO lines.  Typically access to a CO line requires adding a 
digit (e.g., 9) to the auto-dial number.  Also, a “pause” may be required in the auto-dial number.  The 
pause typically is required to wait for secondary (CO line) dial tone.  See the example in the Call Button 
Auto-dial Number 1 on page 23. 

In addition to the pause, the auto-dial telephone has a programmable Primary Dial Tone Delay and 
Secondary Dial Tone Delay.  Both delays determine the amount of time the auto-dial telephone will wait 
before dialing the stored telephone number.  The Secondary Dial Tone Delay can only be used if a “9” is 
dialed to gain access to a CO line. 

Programming Legend 

  D  = DTMF digit 0–9, *, or # 
  N  = Numeric digit 0–9 
  L  = 0 - Disable, 1 - Enable 

Содержание 393-001AD





































Отзывы: