background image

 

P

UB

.

 

42004-472B 

 

A

UTO

-D

IAL 

T

ELEPHONE 

M

ANUAL

 

P

AGE 

14 of 33

 

f:\standard ioms - current release\42004 instr. manuals\42004-472b.doc 
01/15

 

Setup 

Hardware Configuration 

The hardware configuration options are explained in detail in the following sections, and the necessary 
jumper settings are identified to enable or disable each option.  Reading each section and recording the 
selected options prior to making the necessary changes is recommended.  Create a record of your settings 
using Table 2 on page 15.  See Figure 11 on page 16 for the jumper locations. 

Auto-answer Configuration 

Factory Setting

:  Auto-answer feature enabled 

The Auto-answer feature enables or disables the automatic answering of an incoming call, which allows 
TMA to monitor the health of this telephone via polling with SMART operation enabled and remote 
programming in standard mode.  When the Auto-answer feature is enabled, the telephone automatically 
answers the call and attempts to communicate with TMA.  If the caller is not TMA, the telephone 
automatically transitions to a standard two-way communication. 

Enable

: J14 jumper in position 

EN

Disable

: J14 jumper in position 

DIS

 (Do not use this setting except under the direction of GAI-Tronics 

personnel.) 

N

OTE

:

  The Auto-answer feature must be enabled to allow the GAI-Tronics Telephone Management 

Application PC to contact the telephone or to allow remote Touch Tone programming. 

Polarity Configuration 

Factory Setting

: Non-polarity sensitive 

This telephone can be configured to be polarity or non-polarity sensitive.  With the non-polarized setting, 
the telephone operates regardless of tip and ring polarity.  With the polarized setting, the telephone only 
operates with the telephone line’s positive terminal connected to the tip.  Use the Polarity Sensitive 
setting to allow a line voltage reversal disconnect signal to disconnect the call. 

Non-polarity Sensitive

: J6 jumper in position 

NON

Polarity Sensitive

: J6 jumper on in position 

POL

DTMF Gain Select Configuration 

Factory Setting

: Low Gain selected. 

Two gain selections are available in the DTMF detection circuit.  In most installations, the low gain 
setting is recommended.  The high gain setting may be necessary if the telephone is not responding to 
manual or TMA-generated DTMF commands. 

Low Gain Selected

: J17 jumper in position 

LO

High Gain Selected

: J17 jumper in position 

HI

Содержание 393-001AD





































Отзывы: