RED COMPACT 14-2015 Скачать руководство пользователя страница 60

Страница: 60 / 76

11 - SAFETY DEVICES AND ALARMS

ALARM SIGNALLING

When a condition occurs other than the one expected for regular operation of the boiler, an alarm is triggered.

The reason for the alarm is given on the control panel. The sound signal is not enabled for alarms A01-A02 in order not to disturb the user

when there is an absence of pellets in the night tank.

Panel signalling

type of problem

Solution

A01

The flame does not light

Check the level of pellets in the tank.

Check that the brazier is correctly positioned in its

seat and has no build-up or unburned material.

Make sure the ignition plug warms up.

Thoroughly empty and clean the brazier before

restarting.

A02

The flame is extinguished unexpectedly.

Check the level of pellets in the tank.

A03

Thermostats alarm

The temperature of the pellet hopper or the

water temperature exceeds the safety threshold.

Wait until the end of the cooling phase, stop the alarm

and re-ignite the boiler setting the supply of fuel to

minimum (SETTINGS menu - pellet recipe). If the

alarm persists, contact the service centre.

A04

Smoke overtemperature

The set smoke threshold has been exceeded. Reduce

the load of pellets (SETTINGS menu - Pellet recipe).

A05

Pressure switch alarm

Fumes pressure switch intervention or water

pressure insufficient.

Check for chimney obstructions / door open or the

pressure of the hydraulic system.

A08

Anomalous operation of smoke fan.

If the alarm persists, contact the service centre.

A09

Fault with the smoke sensor.

If the alarm persists, contact the service centre.

A19

Fault with water sensor.

Water sensor detached / interrupted / defective / not

recognised.

A20

Puffer probe alarm.

Puffer probe detached / interrupted / defective / not

recognised.

Service

Routine maintenance warning (does not seize) When this blinking message appears upon start-up, it

means it is time to carry out scheduled maintenance.

Call the assistance centre.

ALARM RESET

NEVER open the appliance door whilst the stove is either in the initial startup or on its shut down cycle, pellets will

still be smoldering or therefore volatiles may be present.

ATTENTION!

If during operation or initial ignition you encounter smoke spillage in to the room from the appliance or the flue

then please switch off the appliance, ventilate the room and contact the installation / service engineer immediately.

Содержание COMPACT 14-2015













































































Результаты поиска

Содержание COMPACT 14-2015

Отзывы:

Похожие инструкции для COMPACT 14-2015

Бренды по названию

Популярные бренды

RED COMPACT 14-2015, Руководство по установке

Результаты поиска

Содержание COMPACT 14-2015

Отзывы:

Похожие инструкции для COMPACT 14-2015

Бренды по названию

Популярные бренды