background image

62

U

B

C

D

E

F

A

13 - MAINTENANCE AND CLEANING

CLEAN THE EXCHANGER AND THE COMPARTMENT BENEATH THE BRAZIER EVERY 2/3 DAYS

Cleaning the exchanger and the compartment beneath the brazier is a simple operation but very important if the boiler is to maintain 

optimal performance.

We therefore recommend cleaning the internal exchanger every 2-3 days, performing these simple operations in sequence:

• 

Activate the "CLEANING" function 

- with the boiler off press - menu, select "Settings", with the arrows <> select "Cleaning", 

confirm with the "Menu" key, activate the cleaning "ON" with the + - keys. This procedure starts the smoke extractor on the 

maximum setting to expel the soot that becomes dislodged when the exchanger is cleaned.

• 

Clean the pipe unit 

– Using the hook provided “

U

” shake the rods located under the front boiler cover vigorously 5-6 times. This 

should remove the soot that has deposited on the smoke ducts of the exchanger during normal use of the boiler (

fig. 1

).

• 

Deactivate the "CLEANING" function 

- this function is deactivated automatically after two minutes. If you need to stop the 

function sooner, press the "Esc" key.

• 

Clean the smoke conveyor compartment (fig.2) -

 The boiler is equipped with a removable ash drawer "

C

" which collects any 

accumulations of soot and ash. 

•  When done cleaning, close the cover and ash tray.

If the cleaning is not done every 2-3 days, the boiler could go into alarm caused by ash clogging after several hours 

of operation.

Figure 1

Figure 2

Содержание COMPACT 14-2015













































































Отзывы: