background image

20

3-DRAWINGS AND TECHNICAL CHARACTERISTICS

TECHNICAL CHARACTERISTICS

COMPACT 14

Product class (EN 303-5/2012)

5

Rated thermal capacity of the firebox

13.6 kW (11696 kcal/h)

Nominal output power:

12.3 kW (10578 kcal/h)

Minimum output power

3.3 kW (2838 kcal/h)

Efficiency at Max

90.6%

Efficiency at Min

91.5%

Temperature of exhaust smoke at Max

108°C

Temperature of exhaust smoke at Min

52.5°C

Max configurable temperature

80°C

Max operating temperature

95°C

Particles/OGC/Nox (10%O

2

)

22 mg/Nm

3

 - 1 mg/Nm

3 - 

207 mg/Nm

3

CO at 10% O

2

 at Min and at Max

0.022 - 0.007%

CO

2

 at Min and at Max

8.1 - 9.9%

Recommended draught at Max power

0.10 mbar - 10 Pa

Recommended draught at Min power

0.05 mbar - 5 Pa

Smoke mass

9.1 g/sec

Hopper capacity

35 litres 

Type of pellet fuel

Pellet diameter 6-8 mm and size 3-40 mm

Pellet hourly consumption

Min ~ 0.85 kg/h* - Max ~ 3 kg/h*

Autonomy

At min ~ 27 h* - At max ~ 8 h*

Heatable volume m

3

280/40 - 319/35 - 373/30**

Water content

20 litres

Max operating temperature

3 bar - 300 kPa

Combustion air inlet

0 50 mm

Smoke outlet

0 100 mm

Air intlet

100 cm

2

Rated electrical power (EN 60335-1)

115 W (Max 420 W)

Supply voltage and frequency

230 Volt / 50 Hz

Net weight

190 kg

Weight with packaging

200 kg

* Data that may vary depending on the type of pellets used.

** Volume that can be heated, according to the power requirement in m

3

 (respectively 40-35-30 Kcal/h per m

3

)

Содержание COMPACT 14-2015













































































Отзывы: