INSTALL THE DSMC2 SIDE HANDLE
WARNING:
Before installing or removing this item, you MUST turn off the camera.
REQUIRED TOOLS:
T10 TORX driver (if a Sidekick Cover or DSMC2 Sidekick is installed), M2.5 hex key
1. Turn off the camera.
2. If a Sidekick Cover or DSMC2 Sidekick is installed, remove the device:
A. Use a T10 TORX driver to remove the four (4) screws on the Sidekick Cover or DSMC2 Sidekick.
B. Remove the Sidekick Cover or DSMC2 Sidekick.
3. Place the DSMC2 Side Handle in the slot where the lip of the Sidekick Cover was installed.
4. Press the DSMC2 Side Handle down flush along the side of camera.
5. Tighten the three (3) captive screws and the thumbscrew (in the lower left corner) using an M2.5 hex key. DO NOT
FULLY TIGHTEN.
NOTE:
If you are unable to reach the thumbscrew with a hex key, hand-tighten the thumbscrew.
6. Fully tighten the three (3) screws and the thumbscrew using an M2.5 hex key.
WARNING:
DO NOT OVERTIGHTEN.
NOTE:
If you are unable to reach the thumbscrew with a hex key, hand-tighten the thumbscrew.
REMOVE THE DSMC2 SIDE HANDLE
WARNING:
Before installing or removing this item, you MUST turn off the camera.
REQUIRED TOOLS:
M2.5 hex key
1. Turn off the camera.
2. Use an M2.5 hex key to loosen the three (3) captive screws and the thumbscrew (in the lower left corner).
NOTE:
If you are unable to reach the thumbscrew with a hex key, loosen the thumbscrew by hand.
3. Remove the DSMC2 Side Handle from the camera.
REMOVE THE DMSC2 SIDE HANDLE GRIP
NOTE:
You may replace the original grip of the DSMC2 Side Handle with a third-party grip. However, RED does not
test third-party grips, and cannot confirm if the third-party device will have the same functionality, quality, or strength
as the original grip included by RED in the DSMC2 Side Handle. Damage to the DSMC2 Side Handle or other
components of the camera system caused by using third-party accessories is not covered under warranty.
REQUIRED TOOLS:
5 mm hex key
1. Use a 5 mm hex key to remove the M6 x 90 mm screw at the bottom of the grip.
2. Pull the grip down and away from the DSMC2 Side Handle.
INSTALL THE DSMC2 SIDE HANDLE GRIP
NOTE:
You may replace the original grip of the DSMC2 Side Handle with a third-party grip. However, RED does not
test third-party grips, and cannot confirm if the third-party device will have the same functionality, quality, or strength
as the original grip included by RED in the DSMC2 Side Handle. Damage to the DSMC2 Side Handle or other
components of the camera system caused by using third-party accessories is not covered under warranty.
REQUIRED TOOLS:
5 mm hex key
1. Place the original RED grip at the bottom of the DSMC2 Side Handle.
2. Use a 5 mm hex key to install the orignal M6 x 90 mm screw in the bottom of the grip.
C O PYR I G HT © 2 0 1 7 R ED.C O M , I NC
9 5 5 - 0 1 2 7 _V 6 .3 , R EV - M
|
4 0
RED RAVEN OPERATION GUIDE
Содержание RED DRAGON 4.5K
