SERIAL
NOTE:
CTRL and GIG- E ports are only available on select DSMC2 expanders. For more information, go to
"Input/Output Connectors" on page 193
.
The camera can communicate to external devices via the CTRL and the GIG- E connectors (camera- to- camera
communication is possible only via GIG-E).
Select one of the following protocols from the
Serial Protocol
drop-down menu:
None (Default)
Element Technica
3ality SPC 7XXX
REDLINK Command Protocol
ETHERNET
NOTE:
The GIG-E port is only available on the DSMC2 REDVOLT Expander. For more information, go to
.
Use the settings on the Ethernet tab to configure the GIG-E port. Each camera or device requires a unique IP address.
For camera-to-camera communication via Ethernet, both cameras need to be in the same sub-net (have the same
netmask address) and have the same gateway address.
Enable DHCP
: Enables DHCP. If a DHCP-server is available in the communications network, the camera obtains
an IP address, netmask address, and gateway address automatically from the DHCP server. You cannot manually
enter anything in the IP Address, Netmask, and Gateway fields when this check box is selected.
Enable Camera to Camera
: A change to settings on this camera is sent to other cameras via the network as a
SET command (as UDP packets). The SET command then sets the property on other cameras. If this camera
receives a SET command, the camera does not send the command to other cameras/devices.
Enable External Control
: This camera can be controlled via TCP/IP from an external device.
WIFI
The camera offers a WiFi connection that provides communication support for third-party applications. The camera
uses the REDLINK
®
Command Protocol (RCP) to communicate information between the camera and an application.
As with all wireless devices, the communication range may be affected by the environment and any radio frequency
(RF) interference that may be present. The WiFi frequency is 2.4 GHz.
There are two (2) ways to connect the camera to a device:
Ad-Hoc mode
: The camera and your device connect to each other.
Infrastructure mode
: The camera and your device both connect to an access point, and communicate through
that wireless network.
NOTE:
To connect the camera to an app, the app must have been programmed using the REDLINK SDK, which is
available through the REDLINK Development Kit.
NOTE:
The WiFi antenna is integrated into the fan grill (top side of camera). For optimal WiFi performance, do not
obstruct the antenna with any accessory, mounting plate, or mounting rail.
CONNECT WIRELESSLY TO A DEVICE VIA AD-HOC MODE
In Ad-Hoc mode, the camera and your device connect to each other. To connect the camera to your device via an ad-
hoc network, follow the instructions below:
1. Go to
Menu
>
Settings
>
Setup
>
Communication
.
2. Select the
WiFi
tab.
C O PYR I G HT © 2 0 1 7 R ED.C O M , I NC
9 5 5 - 0 1 2 7 _V 6 .3 , R EV - M
|
1 0 9
RED RAVEN OPERATION GUIDE
Содержание RED DRAGON 4.5K
