background image

door arm, fasteners and miscellaneous parts. The rail assembly includes the roller chain.

Bolt powerhead to rail assembly using 5/16 x 3/4 flat-hd

ASSEMBLE CHAIN Fig. 3

the power source available and compare it with the

PRELIMINARY INSPECTION

This operator as shipped contains one carton and a rail assembly. The carton contains the powerhead, trolley carriage,

and within 6" of front mounting bracket.

ASSEMBLY INSTRUCTIONS

Visually inspect all parts of the operator for shipping

Tighten all bolts securely.

that the correct operator was shipped to you. Also check

Slide trolley carriage (A), Fig. 1, all the way forward on the

certain that all loose parts are removed before discard-

damage.

bolts and whiz lock nuts furnished in hardware package.

Before proceeding with the installation of your Raynor Trolley Operator, it is advisable that you check the following items:

RAIL AND CARRIAGE ASSEMBLY

Check the nameplate located on the powerhead to verify

Check shipping container for damage. Notify delivering

VISUAL INSPECTION

carrier immediately.

rail assembly with lug (B) facing the open end of the rails

ing packing material.

Unpack powerhead and trolley rail assemblies being

5973129-4

electrical data on the nameplate.

ATTACH POWERHEAD Fig.2

PACKAGING

Apply 3/8" hex nut furnished in hardware package to
adjustment rod (C) and install chain around front idler
sprocket at front of rail assembly and feed under trolley
rail brackets to drive sprocket on powerhead. Feed
adjustment rod around drive sprocket then back to trolley
carriage. Install lock washer and feed through lug (B) of

carriage just far enough to start second nut. Thread other
end of chain through chain keeper (E) as shown.

        Warning! Improper lead in of chain could cause

damage to door, operator or personnel.

Take up slack in chain and tighten cap screw (D). Make

final adjustments of chain tension by adjusting nuts on
rod (C).

FRONT MOUNTING BRACKET

TROLLEY CARRIAGE (A)

LUG (B)

FIG. 1

RAIL ASSEMBLY

POWERHEAD

5/16" x 3/4" FLAT HEAD BOLTS

& WHIZ LOCK NUTS

5/16" x 3/4" FLAT HEAD BOLTS

& WHIZ LOCK NUTS

CHAIN KEEPER (E)

CHAIN KEEPER (E)

5/16" x 1" CAP SCREW (D)

LUG (B)

3/8" HEX NUT

LOCK WASHER

ADJUSTING

ROD (C)

TROLLEY CARRIAGE (A)

FIG. 3

FIG. 2

Содержание ControlHoist 2.0 STANDARD



















Отзывы: