background image

5973129-11

USER AND IMPORTANT SAFETY INSTRUCTIONS

WARNING -

To reduce the risk of severe injury or death:

1.

 READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with door controls. Keep the remote control (where provided) away from children.
3. Personnel should keep away from a door in motion and keep the moving door in sight until it is completely closed or
    opened. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR.
4. Test the doors reversing features at least once a month per instructions supplied with reversing device. If limit
    switches require adjusting, reversing devices must also be re-tested. Failure to adjust the operator properly, may

    cause severe injury or death.
5. For products having a manual release, if possible, use the manual release only when the door is closed. Use
    caution when using this release when the door is in the open position. Weak or broken springs may cause the door

    to fall rapidly, causing severe injury or death.
6. KEEP DOORS PROPERLY OPERATING AND BALANCED. See Door Manufacturer's Owner's Manual. An
    improperly operating or balanced door could cause severe injury or death. Only have a trained door systems

    technician make repairs to cables, springs and other hardware.
7. Only use Raynor approved reversing device as explained on front cover of this installation booklet. Failure to use a
    Raynor approved device may cause severe injury or death.

8.

 SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS:

Operating the 3-Button Control Station:

1.

 Press OPEN button (

The door should move in the open direction

).

2.

 Press STOP button (

The door should stop

).

3.

 Press the CLOSE button (

The door should move in the close direction

).

4.

Release the close button and the door should stop if set up for constant pressure (

The door should continue to close

    if set up for momentary contact

 and has an approved monitored reversing device).

5.

Press stop button (

The door should stop

).

How to verify limit switches are adjusted properly:

1.

Press open button and allow door to fully open. The limit should be adjusted so that bottom of door is about an inch

    above the bottom of the header.

2.

 Press close button and allow door to fully close. The door should just hit the floor and stop. If close limit is set too low, the

    door may hit floor and keep trying to run. This can cause damage to door and operator. If door does not completely seal
    against floor, the problem may be with the floor being un-even.

If the limits are not set properly, and need adjustment, remove power and adjust limits (Refer to page 6).

TEST THE ENTRAPMENT PROTECTION DEVICES:

1.

Open the door.

2.

Place an obstruction in the path of the photo eyes or electric sensing edge.

3.

 Press the CLOSE button. The door should not close if photo eyes are functioning. If a sensing edge is installed, the door

    should close onto the obstruction and reverse to fully open.

4.

Remove the obstruction.

5.

 Press CLOSE button. The door should close.

If door did NOT reverse from obstruction, check entrapment devices.

Содержание ControlHoist 2.0 STANDARD



















Отзывы: