Raven MPV-7100 Скачать руководство пользователя страница 44

Страница: 44 / 50

High Level Check

System Check

Remedy

Air Filter is clogged ( Every 10 hours) this
should be cleaned.

Automatic choke has a manual override
feature. If the curved wire lever above the air
cleaner is pulled out the automatic choke

Push in manual override for choke

Choke is pulled out.

Oil in oil separator from oil level too high

Empty and/or replace oil separator. Clean
pulse line from crankcase to oil separator
Check that engine oil is not overfilled.

Spark Arrestor Clogged

Spark Arrestor has become clogged

Clean with brush remove and replace if
needed.

Air Filter is dirty/clogged

Service the air filter

Fuel filter dirty/clogged

Service the fuel filter

Fuel pump dirty/filled with oil/failure

Clean or replace fuel pump if needed

Spark plug wire

Replace

Magneto failure

Replace

Air Filter is Dirty

Clean/ Replace Air Filter

Rollover vent valve failure and/or vent line
pinched under hood. Hose is pinched by
hood assembly.

Remove gas cap, listen for vacuum sound.
Test vent line and valve to ensure it is
unrestricted. Shorten hose or simply reroute.

Engine shuts off while driving on hills

Low Oil. Oil level switch shuts off engine

Check oil level

Low fuel level

Check fuel level

See if magneto is unplugged. This is a black
wire on the units engine that goes over top. Magneto became unplugged while running

Backfire harness is unpluged

Check all connections on unit.

Along with back fires the unit presents also-
Problems

Check for heavy voltage Spikes as this may
present a system Failure/ Call manufacture
(DGP)

Carburaertor may need to be replaced

Engine runs rough or shuts down when
running

Engine runs, but cannot be shut off

Engine backfires when shut off

Engine runs erratically

ne d

oes

n p

per

Symptom

Engine runs well at no-load but “bogs down”
when loads are connected to generator,
mower is turned on, or driving up a steep hill

Содержание MPV-7100



















































Результаты поиска

Содержание MPV-7100

Отзывы:

Похожие инструкции для MPV-7100

Бренды по названию

Популярные бренды

Raven MPV-7100, Руководство по обслуживанию

Результаты поиска

Содержание MPV-7100

Отзывы:

Похожие инструкции для MPV-7100

Бренды по названию

Популярные бренды