Raven DCS 700 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 62

background image

15

d)

After desired speed is set, depress

. HIGH OFFSET is now set.

e)

Depress

to advance to SPINNER LOW OFFSET.

2)

SPINNER LOW OFFSET

a)

GRAN display will show "oFS". LIQ display will show "SpLo". DATA display

will show "2".

b)

Depress

.

c)

Depress

and spinner will stop rotating. Depress and hold

until the spinner begins to rotate. Depress

and

until

spinner is rotating at the minimum speed desired.

d)

After desired speed is set, depress

. LOW OFFSET is now set.

e)

Depress

to advance to GRANULAR HIGH OFFSET.

3)

GRANULAR HIGH OFFSET

When setting the Granular offsets the truck must be running and associated

hydraulics turned on. Place POWER switch on GRAN, SPINNER knob on "1",

RATE knob on "M", and MASTER switch ON.

a)

GRAN display will show "oFS". LIQ display will show "Grhi". DATA display

will show "254".

b)

Depress

.

c)

Depress

to start the auger/bed turning. The RPM's of the granular

motor/shaft and "oFS" will alternately be displayed in the GRAN display.

While auger/bed is turning, depress and hold

until the RPM's begin

to decrease. Depress

to slowly increase RPM's until the maximum

RPM is noticed, then increase offset value displayed in the DATA display

by an additional 10.

«
...
17
18
19
20
21
...
»

Содержание DCS 700































































Отзывы:

Нет отзывов

Похожие инструкции для DCS 700

Бренд: Zetec Страницы: 23

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

Бренд: Abicor Binzel Страницы: 92

Бренд: Patty-O-Matic Страницы: 28

SC 2 Deluxe EasyFix

Бренд: Kärcher Страницы: 12

Бренд: Kärcher Страницы: 16

Бренд: B medical systems Страницы: 28

INTRAmatic 31 ES

Бренд: KaVo Страницы: 52

Бренд: Airway Страницы: 2

Бренд: Crazy Foil Страницы: 8

Бренд: Nuvo Страницы: 2

Бренд: unix Corporation Страницы: 6

Advisor Guide Pedestrian Signal

Бренд: Campbell Страницы: 14

Бренд: Handicare Страницы: 18

Бренд: Nakamichi Страницы: 12

Бренд: Launch Страницы: 15

Бренд: RayLight Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды