Raven DCS 700 Скачать руководство пользователя страница 23

Страница: 23 / 62

Place MASTER switch to OFF.

Weigh the truck and record the weight as weight #2.

Depress

. The GRAN display will show "CAL". The LIQ display will show

"Grto". The DATA display will show "0".

Calculate and enter in the total pounds (kg) of material unloaded.

EXAMPLE:

Weight #1 = 32590

Weight #2 = -31450

Total unloaded

1140

Enter 1140 pounds (kg) as "Grto"

10)

After total pounds are entered the DATA display will show "0".

11)

Depress

and the DATA display will show the new Meter Cal number for that

product.

VERIFYING "GRAN METER CAL"

Factors which can affect the product GRAN METER CAL numbers are the product

particle size, density, temperature, and humidity. Always calibrate the material

you have purchased. Complete INITIAL CONSOLE PROGRAMMING before proceeding with

this procedure. The GRAN METER CAL value is verified using the following

procedure:

Use a pre-weighed box to capture the material as it is metered out.

Verify calculated GRAN METER CAL value is entered into

With the MASTER switch in the OFF position, place RATE knob to "M".

Depress

. The GRAN display will show "SAnd". The LIQ display will show "dAY".

The DATA display will show the volume. Depress

to advance the GRAN display

to Salt, Prd1, or Prd2. Enter a "0" in this key.

Place MASTER switch to SEL and verify the correct product is displayed or depress

and

to select the appropriate product. Place MASTER switch to ON

to begin unloading material. Use the manual INC/DEC switch to adjust the auger/

bed speed. During verification test, monitor material to ensure bridging or

tunneling does not occur.

Содержание DCS 700































































Результаты поиска

Содержание DCS 700

Отзывы:

Похожие инструкции для DCS 700

Бренды по названию

Популярные бренды

Raven DCS 700, Инструкция по установке и обслуживанию

Результаты поиска

Содержание DCS 700

Отзывы:

Похожие инструкции для DCS 700

Бренды по названию

Популярные бренды