background image

BATTERY AND CHARGER 

The first step in preparing a new tool for operation 
is to fully charge the new Battery . New Batteries 
are shipped discharged and must be charged for 
24 hours before first use . All subsequent charges 
will require at most a 3 hour charge . 

WARNING

 

Important Charging Notes

CHEMICAL/EXPLOSION 
HAZARD Read ALL instructions 
before charging or using battery . 

Failure to follow ALL instructions may result in fire, 
severe burns, or release of toxic materials .   

Battery Disposal:

 The EPA certified RBRCQ

®

 

Battery Recycling Seal on the nickel-cadium  
(Ni-Cd) battery indicates Ramset is voluntarily 
participating in an industry program to collect and 
recycle these batteries at the end of their useful 
life, when taken out of service in the United States 
or Canada . The RBRCQ

®

 program provides a  

convenient alternative to placing used Ni-Cd  
batteries into the trash or the municipal waste 
stream, which may be illegal in your area . Please 
call 1-800-8-BATTERY™ (1-800-822-8837) for 
information on Ni-Cd battery recycling and disposal  
in your area . Ramset’s involvement in this program 
is part of our commitment to preserving our envi-
ronment and conserving our natural resources . 

CHARGING INSTRUCTIONS 

1 .  Connect the round plug of the wall mount unit 

to the back of the charger base and plug the 
wall mount unit into any 120V AC outlet . 

2 .  Set the charger base on a stable surface and 

insert the battery, terminals, into the opening of 
the charger base . 

3 .  The GypFast charger incorporates an LED Light 

to inform the user of the battery charge level . 

  A red light will illuminate at all times during a 

charge cycle.  
Lit green light  

  

 

 

=  battery at FULL capacity 

  The red light will not be lit when the battery 

is at full charge. 

CHARGING DONT’S

•  Do not charge battery when temperature 

 

is below 40°F (5°C). 

•  Do not drop battery or charger.

•  Do not allow metal objects to come in 

 

contact with battery terminals. 

•  Do not puncture or attempt to open battery 

case or cells. 

•  Do not store battery where it will be subjected

  

to temperatures above 120°F (49°C). 

•  Do not incinerate battery. 

• 

Do not use a defective battery charger, one that 
overheats and/or smokes when plugged in. 

THE BATTERY AND CHARGING SYSTEM

7

THE BATTERY AND CHARGING SYSTEM

Battery

Charger Base

Wall Mount Unit

Ramset Cordless Charging System

Содержание GYPFAST



















Отзывы: