NOTE:
•
The Automatic High Beam Headlamp Control can be
turned on or off by selecting “ON” under “Auto Dim
High Beams” within your Uconnect settings, as well
as turning the headlight switch to the AUTO position.
Refer to “Uconnect Settings” in “Multimedia” for
further information.
•
Broken, muddy, or obstructed headlights and tail-
lights of vehicles in the field of view will cause head-
lights to remain on longer (closer to the vehicle).
Also, dirt, film, and other obstructions on the wind-
shield or camera lens will cause the system to func-
tion improperly.
•
To opt out of the Advanced Auto High Beam Sensitiv-
ity Control (default) and enter Reduced High Beam
Sensitivity Control (not recommended), on vehicles
equipped with mirror controlled automatic high
beams and without the forward facing camera,
toggle the high beam lever six full on/off cycles
within 10 seconds of placing the ignition in the ON
position. The system will return to the default setting
when the ignition is OFF.
If the windshield or Automatic High Beam Headlamp
Control mirror is replaced, the mirror must be re-aimed
to ensure proper performance. See a local authorized
dealer.
To Activate
1. The Automatic High Beams are enabled through the
Uconnect system. Refer to “Uconnect Settings” in
“Multimedia” for further information.
2. Turn the headlight switch to the AUTO headlight
position.
3. Push the multifunction lever away from you (toward
front of vehicle) to engage the high beam mode.
NOTE:
The Automatic High Beams will not activate until the
vehicle is at or above 12 mph (20 km/h).
To Deactivate
1. Pull the multifunction lever toward you (or rearward
in vehicle) to manually deactivate the system (nor-
mal operation of low beams).
2. Push back on the multifunction lever to reactivate
the system.
The Automatic High Beams can also be deactivated
through the Uconnect system. Refer to “Uconnect Set-
tings” in “Multimedia” for further information.
FLASH-TO-PASS
You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
will cause the high beam headlights to turn on, and
remain on, until the lever is released.
AUTOMATIC HEADLIGHTS —
IF EQUIPPED
This system automatically turns your headlights on or
off based on ambient light levels. To turn the system
on, turn the headlight switch to the extreme clockwise
position aligning the indicator with the AUTO on the
headlight switch. When the system is on, the Headlight
Time Delay feature is also on. This means your head-
lights will stay on for up to 90 seconds after the ignition
is placed in the OFF position. To turn the automatic sys-
tem off, turn the headlight switch counterclockwise to
the O (off) position.
NOTE:
The engine must be running before the headlights will
come on in the Automatic mode.
DIRECTIONAL LED HEADLAMP
SYSTEM — IF EQUIPPED
This is a system consisting of LED (low/high beam)
headlights that incorporate dynamic cornering with
5-degree inboard/15-degree outboard swivel. The
headlights continuously and automatically adapt to the
driving conditions around bends or when cornering
based on steering wheel angle.
The system directs the headlights to light up the road in
the best way, taking into account the speed of the
vehicle and the bend or corner angle, as well as the
speed of the vehicle while the steering wheel is being
turned.
The adaptive lights are automatically activated when
the vehicle is traveling above approximately 5 mph
(8 km/h).
This system can be turned on/off through the Uconnect
Settings under “Steering Directed Lights”. Refer to
Uconnect Settings in “Multimedia” for further
information.
PARKING LIGHTS AND PANEL
LIGHTS
To turn on the parking lights and instrument panel
lights, from the O (off) position, rotate the headlight
switch clockwise to the first detent. To turn off the park-
ing lights, rotate the headlight switch back to the O (off)
position.
40
GETTING TO KNOW YOUR VEHICLE
