Raleigh Audio Premium Extreme RAKK dac Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 65

background image

————————————————————————————

Wire the Outputs

7.

Connect the orange/black twisted pair from the Right Output RCA jack to the “Right Output”
pads on the Active Output. Connect the orange wire to the “R+” pad and the black wire to the
“R-” pad.

8.

Connect the orange/black twisted pair from the Right Output XLR jack to the “Right Output”
pads on the Active Output. Connect the orange wire to the “R+” pad and the black wire to the
“R-” pad.

9.

Connect the blue/black twisted pair from the Left Output RCA jack to the “Left Output” pads
on the Active Output. Connect the blue wire to the “L+” pad and the black wire to the “L-”
pad.

10.

Connect the blue/black twisted pair from the Left Output XLR jack to the “Left Output” pads
on the Active Output. Connect the blue wire to the “L+” pad and the black wire to the “L-”
pad.

————————————————————————————

41

«
...
40
41
42
43
44
...
»

Содержание Premium Extreme RAKK dac


































































Отзывы:

Нет отзывов

Похожие инструкции для Premium Extreme RAKK dac

SOLECTRIA XGI 1500 Series

Бренд: YASKAWA Страницы: 70

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 118

VARISPEED-616G5

Бренд: YASKAWA Страницы: 355

Бренд: ADS Technologies Страницы: 6

CIMR-XC2 Series

Бренд: YASKAWA Страницы: 77

Бренд: Korenix Страницы: 2

Бренд: N-Tron Страницы: 2

Бренд: hc-cargo Страницы: 38

Бренд: V-TAC Страницы: 54

Бренд: Portable Power Technology Страницы: 4

Pocket Inverter 100

Бренд: XPower Страницы: 38

Бренд: Xnexus Страницы: 20

Бренд: B PLUS TV Страницы: 10

Бренд: American Dynamics Страницы: 4

RH l-6K-48ES-5G

Бренд: SOLIS Страницы: 41

Бренд: Channel Master Страницы: 48

ULTRA-SILENT DCA-125USJ

Бренд: MULTIQUIP Страницы: 84

HUBNER BERLIN HOG 75 K

Бренд: Baumer Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды