Raleigh Audio Premium Extreme RAKK dac Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 65

background image

Wire the output jacks:

14.

Connect the output jacks with #22 wire as follows:

•

Strip the insulation from a 3” black wire so that it is bare and tin just the tips.
- Connect one end to pin 3 of the left XLR output jack.
- Feed the wire through the tab on the RCA/XLR switch that is closest to the left XLR
output jack. Solder this tab.
- Wrap the wire around the shell of the left RCA output jack and solder it to the shell.
You might want to use a solder gun to solder the shell.

•

Strip the insulation from a 3” black wire so that it is bare and tin just the tips.
- Connect one end to pin 3 of the right XLR output jack.
- Feed the wire through the tab on the RCA/XLR switch that is closest to the right XLR
output jack. Solder this tab.
- Wrap the wire around the shell of the right RCA output jack and solder it to the shell.

•

Prepare a 1¾” long blue wire and connect it between the center pin of the left RCA
output jack and pin 2 of the left XLR output jack.

•

Prepare a 1¾” long orange wire and connect it between the center pin of the right RCA
output jack and pin 2 of the right XLR output jack.

•

Prepare a 19” long #22 blue/black twisted pair.
- connect the blue wire to pin 2 of the left XLR output jack.
- connect the black wire to pin 3 of the left XLR output jack.

•

Prepare a 17” long #22 orange/black twisted pair.
- connect the orange wire to pin 2 of the right XLR output jack.
- connect the black wire to pin 3 of the right XLR output jack.

36

«
...
35
36
37
38
39
...
»

Содержание Premium Extreme RAKK dac


































































Отзывы:

Нет отзывов

Похожие инструкции для Premium Extreme RAKK dac

Dial-to-IP 5301-DC

Бренд: Accelerated Страницы: 26

Бренд: MADRIX Страницы: 36

Бренд: BARIX Страницы: 2

Бренд: BARIX Страницы: 4

VLT DeviceNet MCA 104

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 138

Бренд: Danfoss Страницы: 108

Бренд: Danfoss Страницы: 149

Бренд: Hama Страницы: 9

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 12

LaCinema Black RECORD

Бренд: LaCie Страницы: 5

Бренд: Velleman Страницы: 28

Бренд: Xantrex Страницы: 78

Бренд: Xanter Страницы: 54

Бренд: Somogyi Elektronic Страницы: 10

Бренд: Daewoo Страницы: 27

SUNNY BOY STORAGE 3.7

Бренд: SMA Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды