Raleigh Audio Premium Extreme RAKK dac Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 65

Raleigh Audio Premium Extreme RAKK dac Скачать руководство пользователя страница 44

Wire the USB Adapter and connect it to the RAKK dac

Skip this section if you do not have a USB Adapter.
Skip this step if you do have a 3-Input I2S Adapter.

18.

Locate the red/black twisted pair from the 8V Regulator and connect it to the 8V pads on the
USB Adapter. Connect the red wire to the “+” pad and the black wire to the “-” pad.

19.

Dress the flat cable close to the chassis and connect it to the “Input 4 I2S” connector on the
RAKK dac

————————————————————————————

Wire the Single-Input I2S Adapter and connect it to the RAKK dac

Skip this step if you do not have a Single-Input I2S Adapter.

20.

Locate the red/black twisted pair from the 5V Regulator and connect it to the 5V pads on the
I2S Adapter. Connect the red wire to the “+” pad and the black wire to the “-” pad.

21.

Dress the flat cable close to the chassis and connect it to the “Input 4 I2S” connector on the
RAKK dac

————————————————————————————

Secure the RAKK dac

22.

Secure the RAKK dac with four 6-32 screws.

————————————————————————————

43

«
...
42
43
44
45
46
...
»

Содержание Premium Extreme RAKK dac


































































Отзывы:

Нет отзывов