Raleigh Audio Premium Extreme RAKK dac Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 65

background image

Wire the Power-on LED

3.

Locate the violet/white twisted pair from the 12V power supply board.

4.

Solder the wires to the LED leads.

•

Connect the violet wire to the anode. The anode is the longer of the two leads.

•

Connect the white wire to the cathode.

————————————————————————————

Wire the Power Switch

The power switch has four terminals (two pairs.) One pair will be used to control the power
on/off and the other pair will be used to provide a fast mute for power off.

5.

Connect the #20 black twisted pair from the white/black power cable to the two terminals on
the power-on switch that are closest to the bottom of the panel.

6.

Connect the #22 black twisted pair from the “external mute” on the Active Output to the two
terminals on the power-on switch that are closest to the top of the panel.

————————————————————————————

48

«
...
47
48
49
50
51
...
»

Содержание Premium Extreme RAKK dac


































































Отзывы:

Нет отзывов

Похожие инструкции для Premium Extreme RAKK dac

Бренд: Patton electronics Страницы: 16

Бренд: Danfoss Страницы: 36

Бренд: Olimpia splendid Страницы: 47

Бренд: K&S BASIC Страницы: 17

Бренд: Karma Страницы: 12

Бренд: CHD Elektroservis Страницы: 20

Бренд: Hubner Страницы: 28

Бренд: Hewalex Страницы: 2

Бренд: Green Power Страницы: 21

Бренд: Z3 Technology Страницы: 15

Бренд: Furrion net-zero Страницы: 32

blueplanet 1502xi

Бренд: Kaco Страницы: 56

Бренд: Fronius Страницы: 190

VFD700-PV-40T00075

Бренд: Veikong Страницы: 70

Бренд: ELECTROCOMPANIET Страницы: 16

Бренд: Brook Страницы: 43

GlobeTrotter Ex GE 0003

Бренд: Option Audio Страницы: 4

Бренд: SICK Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды