Raleigh Audio Premium Extreme RAKK dac Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 65

background image

General

Information

The Extreme RAKK dac is a semi-custom kit, which means that several standard offerings can
be combined in different ways. You can choose to have an optional volume control and optional
select switch. You can choose to have one to six inputs which may be a mix of SPDIF,
AES/EBU, I2S and USB. These are covered in this manual although all of the possible
combinations are not shown. However, those things not shown can be easily inferred from other
things that are shown.

This kit is relatively straightforward to build, but assumes some prior skill with a soldering iron
and some knowledge of electronic components and assembly.

Kit version

Use this manual with the Premium Extreme RAKK dac Mark IV

•

Use the applicable

on-line manuals

for component sub-assemblies.

Required Tools and Supplies

150 to 250 Watt soldering gun
35 to 50 Watt soldering iron
Phillips (cross point) screwdriver
Volt-Ohm-Milliamp Meter
Potentiometer adjustment tool (supplied)
1/16” hex (Allen) wrench (supplied)
5/64” hex (Allen) wrench (supplied)
1.5mm. hex (Allen) wrench (supplied)
2.5mm. hex (Allen) wrench (supplied)
1/4”, 5/16”, 1/2”, 9/16” open-end wrenches
Diagonal cutting pliers
Long-nose pliers
Wire stripper
Solder

Use the soldering gun only to solder the heatsink pins.
Use the soldering iron for all other components.

Support

You may contact us with questions on constructing this kit by sending an e-mail message to

[email protected]

2

«
1
2
3
4
5
...
»

Содержание Premium Extreme RAKK dac


































































Отзывы:

Нет отзывов

Похожие инструкции для Premium Extreme RAKK dac

Бренд: Panasonic Страницы: 12

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 2

Бренд: Yamaha Страницы: 2

Бренд: Z3 Technology Страницы: 86

Бренд: OST Страницы: 2

Бренд: Allied Telesis Страницы: 6

Бренд: B&K Страницы: 2

Бренд: KanexPro Страницы: 32

Бренд: FOLSOM Страницы: 61

Бренд: Vacon Страницы: 102

Бренд: TRUELOOK Страницы: 12

XBMC Clearstream

Бренд: Triotech Страницы: 16

Бренд: Parasound Страницы: 7

Бренд: Parker Страницы: 172

Бренд: Tektronix Страницы: 41

Бренд: TIE Страницы: 4

Бренд: Jarol Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды