Rail King SD70ACe Скачать руководство пользователя страница 46

Страница: 46 / 56

Conventional DC

Start-up

Solution

Sound

Solution

When I apply power to the track my
engine doesn't do anything. No lights,
no sound, no nothing.

I have no sound from my engine, but
my lights are on and it moves just fine.

There's a crackling sound from my
engine

My engine isn't smoking at all

My engine's smoke output is low

Check to see if that section of track has power.
Use a voltmeter or a lit passenger car.

Slide the engine a couple of feet in either
direction, you may have a bad track section

Have you got that section electrically isolated
with a toggle switch or other device?

Check the volume pot on your tender. Full CW
= Max volume

Check to see if a screw or some other material
hasn't lodged itself in the underside of the
chassis or tender

Make sure smoke volume pot is turned full CW

If you just filled it with smoke fluid sometimes
the fluid can make a seal in the stack. Blow
down the stack to clear the air bubble

Check the Tender/Boiler drawbar connection.
You've got to have them locked together

If you've been running your engine in DCS or

DCC mode the smoke may have gotten set to
Low or Med. With the engine running in DCS or
DCC set the smoke back to High. It'll remember
what you last set it as when you run it again in
Conventional DC

Check for an obstruction in the smoke stack

Add 10-12 drops of smoke fluid

Smoke

Solution

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

Содержание SD70ACe

























































Результаты поиска

Содержание SD70ACe

Отзывы:

Похожие инструкции для SD70ACe

Бренды по названию

Популярные бренды

Rail King SD70ACe, Руководство по эксплуатации

Результаты поиска

Содержание SD70ACe

Отзывы:

Похожие инструкции для SD70ACe

Бренды по названию

Популярные бренды