Rail King SD70ACe Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 56

background image

Volume

Solution

The sounds seem distorted, especially
when the Horn or bell is activated.

No Sound

®

Proto-Sound 3.0 volume is set too high.
Turn the volume control knob on the bottom
of the chassis counter-clockwise to reduce
the volume.
Volume is set too low, adjust volume control
knob on the bottom of the chassis clockwise
to increase the volume or check connector to
speaker.

Lock-out

Solution

I can't get the engine to run after I power
up the transformer. It sits still with the
diesel and compressor sounds running.
The engine won't lock into forward,
neutral, or reverse.

The engine maybe locked into the neutral
position. Follow the procedure in the "Lock
into a Direction" section to unlock the
engine's direction. Engine speed must be
below 10 scale mph (approx. 10 volts or less
in conventional mode).

PFA

Solution

Once in PFA, the engine doesn’t go into
reverse.

When the PFA enters its last sequence
the bell automatically comes on

When PFA is enabled, pressing the
whistle and bell has no effect

I push the direction button but the next
sound clip in the sequence does not
play or the engine does not come out of
PFA after fourth press of the direction
button.

So that PFA effects can be as realistic

®

as possible, Proto-Sound 3.0 disables
the reversing unit whenever PFA is
enabled. This way the engine remains
still at its stop as the operator cycles
through the PFA sequences.
PFA is programmed to start ringing the
bell at that point. After approximately 12
seconds, it will automatically turn off.
Because PFA must control various

®

effects in each sequence, Proto-Sound
3.0 takes control of these sound effects
until you exit PFA
Each PFA clip must play for aprox. 30
seconds before PFA will advance to the
next step in the PFA cycle. Wait at least
30 seconds in each PFA sound clip
before pressing the direction button.

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

45

«
...
43
44
45
46
47
...
»

Содержание SD70ACe

























































Отзывы:

Нет отзывов

Похожие инструкции для SD70ACe

Traffic Light-Grand

Бренд: Jamara Страницы: 4

Mercedes-Benz Arocs

Бренд: Jamara Страницы: 4

Mercedes-AMG GT

Бренд: Jamara Страницы: 8

Liebherr 2,4 GHz

Бренд: Jamara Страницы: 8

Бренд: Jamara Страницы: 20

Beaver DHC 2 V2

Бренд: Jamara Страницы: 24

Бренд: Jamara Страницы: 16

Бренд: Jamara Страницы: 8

Techno Gears Marble Mania Raceway

Бренд: The Learning Journey Страницы: 44

Бренд: Tronhelicopters Страницы: 43

Бренд: Hobby King Страницы: 15

Бренд: marklin Страницы: 20

Бренд: Trix Страницы: 32

Fur Real Friends Baby Cuddles My Giggly Monkey Happy to See Me Pets

Бренд: Hasbro Страницы: 2

SBach 342 Thunderbolt

Бренд: SkyLine Страницы: 26

Бренд: PBS KIDS Страницы: 49

Бренд: Hornby Страницы: 2

EI-2309 Language Tutor

Бренд: Educational Insights Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды