Rail King SD70ACe Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 56

background image

One of my lights is out.

None of my lights are on.

Most likely you had been running the engine
in DCC or DCS mode and toggled that light
off. Put it back into one of those modes and
turn that light back on. The engine will
remember that when you run it again in
Conventional DC.
Could be the same reason as “One of my
lights is out”

Is the engine getting power? Check to see if
there if voltage on the track or move the
engine a few feet in either direction.

Lights

Solution

Motion

Solution

When I apply power to the track my
engine starts up (lights and sound) but it
won't move

My engine hesitates at slow speeds.

Lower the track voltage then raise it again.
The engine should start moving. If you apply
greater than 9VDC quickly the engine will just
sit there. Lowering it below 9VDC then raising
it will get the engine moving.

An engine may do this right out of the box if it
has not been lubricated. Follow the lubrication
instructions. Now go ahead and run it.

New engines even after they are lubricated
may take a little bit to get everything run in. Be
a little patient and let it run for a bit. It should
clear up shortly after lubricating and running.

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

47

«
...
45
46
47
48
49
...
»

Содержание SD70ACe

























































Отзывы:

Нет отзывов

Похожие инструкции для SD70ACe

Бренд: Kadee Страницы: 2

Gourmet Kitchen

Бренд: Naomi Kids Страницы: 20

Nieuport 11 Bebe

Бренд: Bengtson Company Страницы: 5

Clock Tower BK 6425

Бренд: Innovative Hobby Supply Страницы: 11

OLD TIMBER BRIDGE

Бренд: Faller Страницы: 4

Бренд: Eduard Страницы: 10

Tribute EP 3D Profile

Бренд: E-FLITE Страницы: 40

Star Wars T-11 Jedi Striker

Бренд: LEGO Страницы: 11

Fordhampton Farm House

Бренд: GAUGEMASTER Страницы: 4

Star Wars Electronic Ask Yoda 72410

Бренд: Hasbro Страницы: 4

Super Mario Adventures with Peach

Бренд: LEGO Страницы: 24

midnight gambler 21005

Бренд: GRAUPNER Страницы: 40

Бренд: Billing Boats Страницы: 32

Бренд: Blade Страницы: 16

Zoom Bf 109E-7 S.A.

Бренд: Eduard Страницы: 3

BARBIE BEACH RANGER 78477

Бренд: Fisher-Price Страницы: 36

GAMETIME HOCKEY RINK

Бренд: OYO Sports Страницы: 60

LASER Sailing Boat & trailer

Бренд: REVELL Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды