Rail King SD70ACe Скачать руководство пользователя страница 3

Страница: 3 / 56

You can obtain replacement parts and replacement instructions from the
M.T.H. Parts Department

(Order Online: www.mthtrains.com,

E-mail: [email protected], Fax: 410-423-0009, Phone: 410-381-2580,
Mail: 7020 Columbia Gateway Drive, Columbia MD 21046-1532)

Set Up Checklist

Assemble RealTrax

Lubricate the engine

Prime the Smoke Unit

Place the engine and cars on the track and couple them together

Connect the transformer and install the DCS Remote Commander

Apply power to run as described in the Basic Operation section of these
instructions.

Diesel Engine

3 Cars

Tools Needed

Cotton Swab or Rag

Philips Screwdriver

M.T.H. Maintenance Kit (30-50051)

Set Includes

Pliers

8-Pieces O-31 Curve

RealTrax (40-1002)

DVD

4-Pieces

Straight RealTrax (40-1001)

Z-500 Transformer

Lighted Lock-On
(40-1003)

Real Trax

wire harness (40-1015)

Scissors

DCS Remote

Commander Set (50-1033)

Remote

Receiver

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

Содержание SD70ACe

























































Результаты поиска

Содержание SD70ACe

Отзывы:

Rail King SD70ACe, Руководство по эксплуатации, Страница: 3 / 56

Результаты поиска

Содержание SD70ACe

Отзывы: