Rail King SD70ACe Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 56

background image

One of my lights is out.

None of my lights are on.

Check your F keys. F0 is the headlight (also
controls the Back-up light) and F5 will toggle
the Cab light

Could be the same reason as “One of my
lights is out”

Is the engine getting power? Check to see if
there is voltage on the track or move the
engine a few feet in either direction.

and firebox light.

Lights

Solution

Motion

Solution

When I apply power and hit F3, my
engine powers up but it won’t move.

My engine hesitates at slow speeds.

An engine may do this right out of the box if it
has not been lubricated. Follow the lubrication
instructions. Now go ahead and run it.

New engines even after they are lubricated
may take a little bit to get everything run in. Be
a little patient and let it run for a bit. It should
clear up shortly after lubricating and running.

This is normal, dial up the speed on your DCC
controller to make your engine move.

PFA

Solution

I hit F4 to start the PFA but the engine
just keeps ringing its bell, that’s all it’ll
do.

Why does my engine run away all by
itself after the PFA is over?

Bring the engine speed to 0. You will now hear
the station arrival sounds (pretty cool, huh?).
Pressing F4 will cycle through the PFA
sequence (check out the PFA section of the
manual for more)
This is normal. The engine will leave the
station at the same speed it entered (when
you hit F4 the first time). You can not control
the speed of your engine while it’s leaving the
station until the bell stops ringing.

Shut Down

Solution

Okay, I give up. What do I have to do to
shut it down?

Well, you can either remove power from
the track or press F3 again.

Lost or Unknown Address

Solution

I can't call up my engine on the address
I believe it to be set at

Perform the 55-55-55 Reset instructions
on page 25

If you are trying to talk to an engine on its
short address you may have set CV29 to
activate long addressing. Try to get a hold of
the engine on its last known long address

Place the engine on the Programming Track
output on your DCC system and write a value
of 3 to CV1

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

49

«
...
47
48
49
50
51
...
»

Содержание SD70ACe

























































Отзывы:

Нет отзывов

Похожие инструкции для SD70ACe

Strike Eagle G1670B Cargo Plane

Бренд: Laser Pegs Страницы: 8

Бренд: Laser Pegs Страницы: 2

Baby Annabell 794982

Бренд: Zapf Creation Страницы: 2

Бренд: Zapf Creation Страницы: 24

150cc Extra 300SP ARF

Бренд: PAU Страницы: 19

Bubble Dinosaur

Бренд: AbleNet Страницы: 8

Бренд: Vollmer Страницы: 5

Slide&Surf SLA.747757

Бренд: Slackers Страницы: 3

Bbaby Mini Woofer BX1986

Бренд: Maison Battat Страницы: 2

Бренд: Eduard Страницы: 5

Alphabert s Pen Pal Phonics

Бренд: VTech Страницы: 16

Бренд: Fisher-Price Страницы: 4

Бренд: BLOTZ Страницы: 2

Бренд: Gym Dandy Страницы: 14

Бренд: Propel RC Страницы: 4

ARCHITECTURE BIG BEN

Бренд: LEGO Страницы: 68

VISION Line 700E Hudson

Бренд: Lionel Страницы: 32

Play The Best T8576W/F

Бренд: Stiga Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды